Front Brake Caliper Mounting Plate Replacement Bendix

Use the brake caliper mounting plate in order to mount all of the stationary brake components. An L or R following the part number cast on the back of the plates indicates left or right side mounting. Some plates may also have an L or R painted on the front.

1. Apply the parking brake.
2. Block the wheels.

Notice: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

3. Remove the brake caliper. Refer to Front Brake Caliper Replacement .
4. Remove the hub and brake rotor assembly. Refer to Front Brake Rotor Replacement .
5. Remove the bolts and washers.
6. Remove the brake caliper mounting plate.
7. Inspect the support rails for rust, corrosion, and wear.
8. Clean the support rails with a wire brush.
9. Inspect the brake caliper mounting plate for cracks or elongated bolt holes.

Replace the mounting plate if necessary.

1. Install the brake caliper mounting plate to the steering knuckle.

Important: Ensure that the threads are clean and greaseless before applying threadlocker.

2. Apply 272 Threadlocker GM P/N 12345493, or equivalent, to the threads of each brake caliper mounting plate bolt.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the bolts and washers.

Tighten

•	Tighten the brake shield bolts to 32 N·m (24 lb ft).

•	Tighten the brake caliper mounting plate bolts to 280 N·m (206 lb ft).

4. Install the hub and brake rotor assembly. Refer to Front Brake Rotor Replacement .
5. Install the brake caliper. Refer to Front Brake Caliper Replacement .
6. Do not remove the brake line from the caliper.
7. Remove the blocks.

Front Brake Caliper Mounting Plate Replacement Dayton Walther

Use the brake caliper mounting plate in order to mount all of the stationary brake components. An L or R following the part number cast on the back of the plates indicates left or right side mounting. Some plates may also have an L or R painted on the front.

1. Apply the parking brake.
2. Block the wheels.

Notice: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

3. Remove the brake caliper (6). Refer to Front Brake Caliper Replacement .
4. Do not remove the brake line from the caliper.
5. Remove the hub and brake rotor assembly. Refer to Front Brake Rotor Replacement .
6. Remove the bolts and washers (3, 5).
7. Remove the brake caliper mounting plate (4).
8. Inspect the support rails for rust, corrosion, and wear.
9. Clean the support rails with a wire brush.
10. Inspect the brake caliper mounting plate (4) for cracks or elongated bolt holes.

Replace the mounting plate if necessary.

1. Install the brake caliper mounting plate (4) to the steering knuckle.

Important: Ensure that the threads are clean and greaseless before applying threadlocker.

2. Apply 272 Threadlocker GM P/N 12345493, or equivalent, to the threads of each brake caliper mounting plate bolt.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the bolts and washers (3, 5).

Tighten

•	Tighten the brake shield bolts to 32 N·m (24 lb ft).

•	Tighten the brake caliper mounting plate bolts to 280 N·m (206 lb ft).

4. Install the hub and brake rotor assembly. Refer to Front Brake Rotor Replacement .
5. Install the brake caliper (6). Refer to Front Brake Caliper Replacement .
6. Remove the blocks.