GM Service Manual Online
For 1990-2009 cars only

Checks

Action

DEFINITION: Engine power variation under steady throttle or cruise. Feels like the vehicle speeds up and slows down with no change in the accelerator pedal.

Preliminary

    • Refer to the Symptoms .
    • Search for bulletins.
    • Be sure driver understands transmission torque converter clutch, and A/C compressor operation as explained in the owners manual. Inform customer how TCC and the A/C clutch operates.

Sensor/System

    • Test the heated oxygen sensors. The heated oxygen sensors should respond quickly to different throttle positions. If not, inspect the HO2S for silicon or other contaminants from fuel or use of incorrect RTV sealant. The sensors may have a white powdery coating. Silicon contamination causes a high but false HO2S signal voltage (rich exhaust indication). The PCM will reduce the amount of fuel delivered to the engine, causing a severe driveability problem. Refer to heated oxygen sensors in Information Sensors/Switches Description .
    • Test the MAF sensor and inspect the related wiring.
    • Test the EGR valve for a stuck open pintle.

Fuel System

    • Test the fuel pressure.
    • Test for contaminated fuel. Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
    • Ensure each injector harness is connected to the correct injector/cylinder. Refer to Engine Controls Schematics .
    • Test items which can cause an engine to run rich (long term fuel trim is significantly in the negative range). Refer to Diagnostic Aids for DTC P0172 Fuel Trim System Rich Bank 1 .
    • Test items that can cause an engine to run lean (long term fuel trim is significantly in the positive range). Refer to Diagnostic Aids for DTC P0171 Fuel Trim System Lean Bank 1 .

Ignition System

    • Test for proper ignition voltage output using the following steps:
       - Clip the J 26792 spark tester to engine ground.
       - Connect one end of a spark plug wire to the spark tester, leave the other end of the spark plug wire to the coil being tested.
       - Connect one end of another spark plug wire to the other coil tower, connect the other end of the spark plug wire to ground.
       - Crank the engine while observing the spark tester, a spark should be observed.
       - Repeat the above steps for each coil.
    • If adequate spark is not present at the coils, test for the following conditions:
       - Coils - Cracks, carbon tracking/arcing, or a resistance value outside the specified range.

Coil Secondary Resistance
5000 - 8000 ohms (5K - 8K ohms)

       - Spark Plug wires - Signs of arcing/cross firing, cracks, carbon tracking, plug boot damage, pinched, incorrect routing, or a resistance value more than the specified value.

Spark Plug Wires Resistance
3280-4921 ohms/meter(1000-1500 ohms/ft).

   Important: Spraying the secondary ignition wires with a light mist of water may help locate an intermittent problem. Ignition components will arc to ground when a secondary component is malfunctioning.

       - Malfunctioning ignition control module.
       - Ignition System Wiring - Loose ignition module feed or ground connection, or damaged system wiring.
    • Remove spark plugs and inspect for the following conditions:
       - Fouled plugs
       - Cracks
       - Wear
       - Incorrect gap
       - Burned or damaged electrodes
       - Incorrect heat range
    • If spark plugs are gas or oil fouled, the cause of the fouling must be determined before replacing the spark plugs.

Additional Tests

    • Test TCC operation. Refer to A Diagnostic Starting Point in 4L60-E Automatic Transmission.
    • Inspect the exhaust system for a possible restriction:
       - Inspect the exhaust system for damaged or collapsed pipes.
       - Inspect the muffler for heat distress or possible internal failure.
       - Test for possible plugged Three-Way catalytic converter. Refer to Restricted Exhaust System Check .