Circuit Description
The throttle position (TP) sensor is used by the powertrain control module (PCM) in order to determine the throttle plate angle for various engine management systems. The TP sensor is a potentiometer type sensor with 3 circuits: a 5-volt reference circuit, a low reference circuit, and a signal circuit. The PCM provides the TP sensor with a 5-volt reference circuit and a low reference circuit. Rotation of the TP sensor rotor from the closed throttle position to the wide open throttle (WOT) position provides the PCM with a signal voltage from less than 1 volt to more than 4 volts through the TP sensor signal circuit. If the PCM detects an excessively low signal voltage, this DTC will set.
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
| • | The TP sensor signal voltage is less than 0.1 volts. |
| • | The above condition is present for more than 2 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
If this DTC is determined to be intermittent, refer to Intermittent Conditions .
Test Description
The number below refers to the step number on the diagnostic table.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |
2 |
Is the voltage is less than the specified value? | 0.1 V | Go to Step 4 | Go to Step 3 |
3 |
Does the diagnostic test fail this ignition? | -- | Go to Step 4 | Go to Step 10 |
4 |
Does the voltage equal the specified value? | 5 V | Go to Step 11 | Go to Step 5 |
5 |
Does the DMM indicate voltage near the specified value? | 5 V | Go to Step 9 | Go to Step 6 |
6 | Use the DMM in order to test the 5-volt reference circuit for an open and for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 7 |
7 | Test all of the 5-volt reference circuits for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 8 |
Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 10 | |
9 | Use the DMM in order to test the TP sensor signal circuit for an open, for a high resistance, and for short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 10 |
10 | Inspect for poor connections at the PCM harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 13 |
11 | Inspect for poor connections at the TP sensor harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 12 |
12 | Replace the TP sensor. Refer to Throttle Position Sensor Replacement . Did you complete the replacement? | -- | Go to Step 14 | -- |
13 | Replace the PCM. Refer to Powertrain Control Module Replacement . Did you complete the replacement? | -- | Go to Step 14 | -- |
14 |
Does the diagnostic test run and pass? | -- | Go to Step 15 | Go to Step 2 |
15 | Use the scan tool in order to observe the stored information, Capture Info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK | |
