DTC Descriptor
DTC P1482: Cooling Fan Speed Output Circuit
Diagnostic Fault Information
Perform the
Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
Circuit/System Description
The engine cooling fan is a variable speed fan. The engine control module (ECM) controls the fan speed by sending a pulse width modulated signal to the cooling fan control module. The cooling fan control module varies the voltage drop across the engine
cooling fan motor in relation to the pulse width modulated signal. The cooling fan speed is effected by many different conditions and can be adjusted from 10% to 90% duty cycle (PWM), 90% is considered high speed fan. When multiple cooling fan speed requests
are received the ECM uses the highest cooling fan speed of all the requests. During normal operation the control circuit voltage will be low and near battery voltage when OFF.
Conditions for Running the DTC
| • | The ignition voltage is between 10 and 18 volts. |
| • | The engine speed is more than 400 RPM. |
Conditions for Setting the DTC
The ECM detects that the commanded state of the driver and the actual state of the control circuit do not match.
Action Taken When the DTC Sets
| • | The ECM will illuminate the malfunction indicator lamp (MIL) ON the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The ECM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data. |
Conditions for Clearing the DTC
| • | The ECM will turn OFF the MIL during the third consecutive ignition cycle that the diagnostic runs and passes. |
| • | The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | Use the scan tool Clear DTC Information function. |
Diagnostic Aids
| • | Cooling fan duty cycle starts when engine coolant temperature reaches approximately 95°C (204°F) and reaches high speed at temperatures above 113°C (235°F). |
| • | Cooling fan duty cycle starts when A/C pressure reaches approximately 1100 kPa (160 psi) and reaches high speed at A/C pressures above 2480 kPa (360 psi) |
| • | At engine oil temperatures above approximately 150°C (302°F) the cooling fan duty cycle will be commanded to high speed. |
| • | At transmission oil temperatures above approximately 132°C (270°F) the cooling fan duty cycle will be commanded to high speed. |
| • | After the vehicle is shut OFF if the engine coolant temperature at key-off is greater than 113°C (235°F) or the A/C pressure is greater than 1720 kPa (249 psi) the cooling fan duty cycle is set to 50%,low speed. If the coolant
temperature drops below 110°C (230°F) and the A/C pressure drops below 1660 kPa (241 psi) the fan will shut OFF. The fans will automatically shut OFF after 2 min. regardless of coolant temperature. |
Reference Information
Schematic Reference
Engine Cooling Schematics
Connector End View Reference
Cooling System Connector End Views
Description and Operation
Cooling System Description and Operation
Electrical Information Reference
Scan Tool Reference
Circuit/System Verification
Ignition ON, command the cooling fan ON and OFF with a scan tool. Observe that the cooling fan turns ON and OFF with each command.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the Fan control module.
- Ignition OFF, test for less than 1.0 ohm of resistance between the ground circuit and ground.
| ⇒ | If greater than 1.0 ohm, test the ground circuit for an open/high resistance. |
- Ignition ON, test for B+ between the battery positive voltage circuit and ground.
| ⇒ | If less than B+, test the battery positive voltage circuit for a short to ground or an open/high resistance. If the COOLFAN fuse is open, test battery positive voltage circuit for a short to ground. |
- With a DMM, test for B+ between the B+ circuit terminal 3 and the control circuit terminal 6.
| ⇒ | If less than B+, test the control circuit for and open/high resistance. If the circuit tests normal replace the ECM. |
- Test for 1.5-.5 ohms of resistance between the low reference terminal 1 and supply voltage terminal 4.
| ⇒ | If not within specified value, test and replace the cooling fan. |
- If all circuits test normal, test and replace the cooling fan control module.
Component Testing
Install a 60A fused Jumper wire between the cooling fan supply voltage terminal 4 and B+. Momentarily install a jumper wire between the cooling fan low reference terminal 1 and ground. The cooling fan should turn ON.
| ⇒ | If the function does not perform as specified, replace the cooling fan. |
Repair Instructions
Perform the
Diagnostic Repair Verification after completing the diagnostic procedure.
