GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2001 🢒 Seville 🢒 Body and Accessories 🢒 Wiring Systems 🢒 Air Inlet Valve Actuator Replacement

Air Inlet Valve Actuator Replacement LHD

Removal Procedure

    Object Number: 291175 Size: SH
  1. Remove the instrument panel (IP) compartment. Refer to Instrument Panel Compartment Replacement in Instrument Panel, Gauges and Console.
  2. Remove the right sound insulator. Refer to Instrument Panel Insulator Panel Replacement - Right Side in Instrument Panel, Gauges and Console.
  3. Remove the dash integration module (DIM) from the bracket. Refer to Dash Integration Module Replacement in Body Control System.
  4. Remove the rear 2 DIM module bracket fasteners.
  5. Reposition the DIM module bracket in order to gain access to the recirculation actuator.

    6. Object Number: 292142 Size: SH
  6. Remove the recirculation actuator retaining fasteners (1).
  7. Remove the electrical connector from the recirculation actuator.

    8. Object Number: 292146 Size: SH
  8. Remove the recirculation actuator.

Installation Procedure

    Object Number: 292146 Size: SH
  1. Install the recirculation actuator.

    2. Object Number: 292142 Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the recirculation actuator retaining fasteners (1).

    3. Tighten
    Tighten the fasteners to 1.4 N·m (12 lb in).

  3. Install the electrical connector to the recirculation actuator.

    4. Object Number: 291175 Size: SH
  4. Position the DIM module bracket to its original position.
  5. Install the rear 2 DIM module bracket retaining fasteners.

    6. Tighten
    Tighten the fasteners to 1.4 N·m (12 ft lb).

  6. Install the DIM module into the bracket. Refer to Dash Integration Module Replacement in Body Control System.
  7. Install the right sound insulator. Refer to Instrument Panel Insulator Panel Replacement - Right Side in Instrument Panel, Gauges and Console.
  8. Install the IP compartment. Refer to Instrument Panel Compartment Replacement in Instrument Panel, Gauges and Console.
  9. Recalibrate the actuators. Refer to Body Control Module (BCM) Programming/RPO Configuration in Body Controls.

Air Inlet Valve Actuator Replacement RHD

Removal Procedure
  1. Remove the instrument panel (IP) compartment. Refer to Instrument Panel Compartment Replacement in Instrument Panel, Gauges and Console.
  2. Remove the left sound insulator. Refer to Instrument Panel Insulator Panel Replacement - Left Side in Instrument Panel, Gauges and Console.
  3. Remove the dash integration module (DIM) from the bracket. Refer to Dash Integration Module Replacement in Body Control System.
  4. Remove the rear 2 DIM module bracket fasteners.
  5. Reposition the DIM module bracket in order to gain access to the recirculation actuator.
  6. Remove the electrical connector from the recirculation actuator.
  7. Remove the recirculation actuator retaining fasteners (1).

    8. Object Number: 292146 Size: SH
  8. Remove the recirculation actuator.

Installation Procedure

    Object Number: 292146 Size: SH
  1. Install the recirculation actuator.

    2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the recirculation actuator retaining fasteners (1).

    3. Tighten
    Tighten the fasteners to 1.4 N·m (12 lb in).

  3. Install the electrical connector to the air inlet actuator.
  4. Position the DIM module bracket to its original position.
  5. Install the rear 2 DIM module bracket retaining fasteners.

    6. Tighten
    Tighten the fasteners to 1.4 N·m (12 lb in).

  6. Install the DIM module into the bracket. Refer to Dash Integration Module Replacement in Body Control System.
  7. Install the left sound insulator. Refer to Instrument Panel Insulator Panel Replacement - Left Side in Instrument Panel, Gauges and Console.
  8. Install the IP compartment. Refer to Instrument Panel Compartment Replacement in Instrument Panel, Gauges and Console.
  9. Recalibrate the actuators. Refer to Body Control Module (BCM) Programming/RPO Configuration in Body Controls.