Notice: Do not damage the MAF sensor screen. A damaged screen could restrict airflow and lead to a driveability concern.

1. Relieve the fuel system pressure. Refer to the Fuel Pressure Relief .
2. Remove the IAT sensor electrical connector (1) from the IAT sensor.
3. Remove the MAF sensor electrical connector from the MAF sensor.
4. Remove the air cleaner intake duct (2).



5. Remove the PCV valve fresh air tube.



6. Remove the cruise control cable (2) from accelerator controls cable bracket (1).
7. Remove the accelerator cable (3) from accelerator controls cable bracket (1).
8. Remove the cruise control cable (2) from throttle body lever.



9. Remove the accelerator control cable (3) from throttle body lever (2).



10. Remove the IAC valve electrical connector (1) from the IAC valve (4).
11. Remove the TP sensor electrical connector (2) from the TP sensor (3).



12. Remove the fuel feed (4) and return lines (2) from the retainer (5) on the accelerator controls cable bracket.



13. Remove the transaxle shift cable clip (1) from the accelerator controls cable bracket.



14. Remove the throttle body (2) from the water crossover (1).



15. Remove the nuts (2) from the accelerator controls cable bracket (3).
16. Remove the accelerator controls cable bracket (3) from the throttle body (1).

Notice: Do not use a cleaner which contains methyl ethyl ketone. This extremely strong solvent may damage components and is not necessary for this type of cleaning.

Notice: The outlet of the air cleaner assembly and the MAF sensor inlet duct must line up when completely installed. Misalignment may cause incorrect airflow readings resulting in MIL illumination or a driveability concern. An improperly installed inlet duct assembly or air cleaner assembly may cause misalignment.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Important: Do Not Reuse the old throttle body gasket.




1. Install the accelerator cable bracket (3) to the throttle body (1).

Tighten
Tighten the bolts (2) to 12 N·m (106 lb in).




2. Position the new throttle body gasket on to the throttle body.
3. Install bolts from the throttle body (2) to water crossover (1).

Tighten
Tighten the bolts to 12 N·m (106 lb in).




4. Install the IAC valve electrical connector (1) to the IAC valve (4).
5. Install the TP sensor electrical connector (2) to the TP sensor (3).



6. Install the accelerator control cable (3) at throttle body lever (2).



7. Install the cruise control cable (2) at throttle body lever.
8. Install the accelerator cable (3) to the accelerator controls cable bracket (1).
9. Install the cruise control cable (2) to accelerator controls cable bracket (1).



10. Install the transaxle shift cable clip (1) to the accelerator controls cable bracket.



11. Install the fuel feed (4) and return pipe (2) to the retainer (5) on to the accelerator controls cable bracket.



12. Install the MAF sensor electrical connector to the MAF sensor.
13. Install the IAT sensor electrical connector (1) from the IAT sensor.
14. Install the air cleaner intake duct clamp to the air cleaner intake air duct (2).

Tighten
Tighten the air cleaner intake duct clamps to 4 N·m (35 lb in).




15. Install the PCV valve fresh air tube.



16. Install the fuel injector sight shield (1) to the engine.
17. Install the fuel injector sight shield nuts (2).

Tighten
Tighten the nuts to 3 N·m (27 lb in ).

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

18. Install the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
19. Install the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
20. Perform the TP sensor learn procedure.

20.1.

Turn ignition to the RUN/ON position.

20.2.

Wait 1 minute.

20.3.

Turn ignition to the LOCK/OFF position.

20.4.

Wait 15 seconds.

21. Perform the IAC Valve Learn Procedure

21.1.

Start and idle the engine for 15 seconds.

21.2.

Turn the ignition to the LOCK/OFF position.

21.3.

Wait 15 seconds

21.4.

Restart the engine and check for proper idle operation.