Was the entire Exterior Lights System Check performed?

--

Go to Step 2

Go to Exterior Lights System Check

1. Turn the ignition switch to the ON position.
2. Connect a scan tool to the data link connector (DLC).
3. Select INPUTS from the dash integration module (DIM) DATA DISPLAY.
4. Place the headlamp switch in the PARK position.

Does the scan tool indicate that the Park Lamps Switch was ON?

--

Go to Step 3

Go to Step 7

Do the headlamps operate properly?

--

Go to Step 4

Go to Step 13

Backprobe the rear fuse block connector C1 with a DMM from battery positive voltage (B+) to cavity F3 (WHT).

Is the voltage within the specified range?

10-15 V

Go to Step 5

Go to Step 15

Replace the PRK LP Relay.

Do all park lamps now operate properly?

--

Go to Exterior Lights System Check

Go to Step 6

Replace the rear fuse block.

Is the rear fuse block replacement complete?

--

Go to Exterior Lights System Check

--

Backprobe the headlamp switch connector with a DMM from battery positive voltage (B+) to cavity A8 (BRN/WHT).

Is the voltage within the specified range?

10-15 V

Go to Step 8

Go to Step 10

1. Disconnect the dash integration module (DIM) connector C2.
2. Disconnect the headlamp switch connector.
3. Backprobe CKT 301 (BRN/WHT) with a DMM from the DIM connector C2 cavity B3 (BRN/WHT) to the headlamp switch connector cavity A8 (BRN/WHT).

Is the resistance less than the specified value?

0.5 ohms

Go to Step 16

Go to Step 9

Repair the open in CKT 301 (BRN/WHT) between the dash integration module (DIM) and the headlamp switch. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Exterior Lights System Check

--

Backprobe the headlamp switch connector with a DMM from battery positive voltage (B+) to cavity A2 (BLK/WHT).

Is the voltage within the specified range?

10-15 V

Go to Step 11

Go to Step 12

Replace the headlamp switch. Refer to Headlamp Switch Replacement .

Is the headlamp switch replacement complete?

--

Go to Exterior Lights System Check

--

Repair the open in CKT 351 (BLK/WHT) between the headlamp switch and S212. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Exterior Lights System Check

--

Backprobe the rear fuse block connector C1 with a DMM from cavity D4 (DK GRN) to ground.

Is the voltage within the specified range?

10-15 V

Go to Step 6

Go to Step 14

1. Remove the PRK LP relay from the rear fuse block.
2. Disconnect the dash integration module (DIM) connector C1.
3. Backprobe CKT 1483 (DK GRN) with a DMM from the rear fuse block connector C1 cavity D4 (DK GRN) to the DIM connector C1 cavity B8 (DK GRN).

Is the resistance less than the specified value?

0.5 ohms

Go to Step 16

Go to Step 17

1. Remove the PRK LP relay from the rear fuse block.
2. Disconnect the dash integration module (DIM) connector C1.
3. Backprobe CKT 1080 (WHT) with a DMM from the rear fuse block connector C1 cavity F3 (WHT) to the DIM connector C1 cavity B5 (WHT).

Is the resistance less than the specified value?

0.5 ohms

Go to Step 16

Go to Step 18

Replace the dash integration module (DIM). Refer to Body Control Module Replacement in Body Control System.

Is the DIM replacement complete?

--

Go to Exterior Lights System Check

--

Repair the open in CKT 1483 (DK GRN) between the rear fuse block and the DIM. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Exterior Lights System Check

--

Repair the open in CKT 1080 (WHT) between the rear fuse block and the DIM. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Exterior Lights System Check

--