DTC B1395 Rear Seat Module
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B1395 03: Device Voltage Reference Output CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Back Panel Position Switch Supply Voltage | B1395 03 | 2 | -- | -- |
Load Floor Position Switch Supply Voltage | B1395 03 | 1 | -- | -- |
Back Panel Position Switch Signal | B1395 03 | 2 | 1 | -- |
Load Floor Position Switch Signal | B1395 03 | 1 | -- | -- |
1. Power third row seat inoperative 2. Power third row seat recline inoperative | ||||
Circuit/System Description
Battery positive voltage is supplied at all times to the seat load floor position switch and the back panel position switch by the rear seat module (RSM). The RSM monitors these battery positive voltage supply circuits for the protection of internal circuitry of the module.
Conditions for Running the DTC
The ignition must be in the ACCESSORY, RUN or CRANK power mode.
Conditions for Setting the DTC
This DTC will set only when the RSM detects that the device switch supply voltage is less than 3 volts.
Action Taken When the DTC Sets
| • | The RSM will not allow seat operation. |
| • | If this condition occurs during seat operation, the operation will be cancelled. |
Conditions for Clearing the DTC
The DTC will clear when the RSM detects that the device switch voltage is greater than 3 volts.
Diagnostic Aids
| • | When the rear folding seat back panel is in the folded position, the load flood position switch is closed to voltage. |
| • | When the rear folding seat is in either the seated or stowed positions, the back panel position switch is closed to voltage. |
Reference Information
Schematic Reference
Connector End View Reference
Power Seat Connector End Views
Electrical Information Reference
Scan Tool Reference
Circuit/System Verification
- Ignition ON, observe the scan tool Load Floor Switch parameter with the seat back panel in the folded position. The reading should be Inactive.
- Ignition ON, observe the scan tool Back Panel Position Switch parameter with the seat in either the seated or stowed positions. The reading should be Active.
Circuit/System Testing
- Ignition OFF, disconnect the (C2) harness connector at the rear seat module.
- Test for infinite resistance between the supply voltage circuit terminal D1 and ground.
- Test for infinite resistance between the signal circuit terminal C10 and ground.
- Test for infinite resistance between the supply voltage circuit terminal D2 and ground.
- Test for infinite resistance between the signal circuit terminal C11 and ground.
- If all circuits test normal, replace the rear seat module.
| ⇒ | If not the specified value, test the supply voltage circuit for a short to ground. |
| ⇒ | If not the specified value, test the signal circuit for a short to ground. |
| ⇒ | If not the specified value, test the supply voltage circuit for a short to ground. |
| ⇒ | If not the specified value, test the signal circuit for a short to ground. |
Repair Instructions
Important: After performing this diagnostic test and the electrical or component repairs have been completed, the folding seat may be in an unknown state and out of calibration with the RSM. Therefore, the RSM must be calibrated before the folding seat system will operate. Refer to Power Folding Seat Calibration .
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for rear seat module replacement, setup, and programming
DTC B1395 Memory Seat Module
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC B1395 02: Device Voltage Reference Output Circuit Shorted to GroundDTC B1395 05: Device Voltage Reference Output Circuit Shorted to Battery or Open
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
5-Volt Reference | B1395 02, B1825 06, B1850 06, B2355 06, B2365 06, B2375 06, B3606 06, B3633 06 | B1825 06, B1850 06, B2355 06, B2365 06, B2375 06, B3606 06, B3633 06 | B1395 05, B1825 01, B1850 01, B2355 01, B2365 01, B2375 01, B3606 01, B3633 01 | B1825 5A, B1850 5A, B2355 5A, B2365 5A, B2375 5A, B3606 5A |
Adjustable Accelerator Pedal Position Sensor Signal | B3633 06, B3633 5A | B3633 06, B3633 5A | B3633 01, B3633 5A | -- |
Adjustable Brake Pedal Position Sensor Signal | B3606 06, B3633 5A | B3606 06, B3633 5A | B3606 01, B3633 5A | -- |
Driver Seat Front Vertical Position Sensor Signal | B2355 06 | B2355 06 | B2355 01 | -- |
Driver Seat Rear Vertical Position Sensor Signal | B2365 06 | B2365 06 | B2365 01 | -- |
Driver Seat Horizontal Position Sensor Signal | B2375 06 | B2375 06 | B2375 01 | -- |
Driver Seat Lumbar Horizontal Position Sensor Signal | B1850 06 | B1850 06 | B1850 01 | -- |
Driver Seat Recline Position Sensor Signal | B1825 06 | B1825 06 | B1825 01 | -- |
Memory Seat/Mirror Sensor Low Reference | -- | B1825 01, B1850 01, B2355 01, B2365 01, B2375 01, B3606 01, B3606 61, B3633 01 | -- | B1825 5A, B1850 5A, B2355 5A, B2365 5A, B2375 5A, B3606 5A |
Circuit/System Description
The memory seat module (MSM) supplies a 5-volt reference voltage to the driver seat horizontal, front vertical, rear vertical, recline, lumbar position sensors and both adjustable pedals position sensors. The MSM monitors this reference voltage to ensure the accuracy of the voltages being returned from the sensors. If the voltage exceeds the normal operating range, errors will occur in the memory recall operations of the seat and adjustable pedals.
Conditions for Running the DTC
The MSM must be powered.
Conditions for Setting the DTC
B1395 02
The reference voltage drops below 4.8 volts for more than 300 mS.
B1395 05
The reference voltage exceeds 5.2 volts for more than 300 mS.
Action Taken When the DTC Sets
| • | All memory seat recall functions will be disabled. |
| • | All memory and manual adjustable pedals functions will be disabled. |
Conditions for Clearing the DTC
| • | The current DTC will clear and set the code to history, 3 seconds after the reference voltage returns to the normal operating range and the ignition is cycled OFF then back to ACC or RUN. |
| • | The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred. |
Diagnostic Aids
| • | The Memory Seat Module (MSM) may be referenced as the Driver Position Module. |
| • | All position sensors use common ground and 5-volt reference circuits. |
| • | If the 5-volt reference circuit is shorted to voltage multiple position sensor codes will set. |
| • | If the 5-volt reference circuit is shorted to ground multiple position sensor codes will set. |
| • | A short to voltage on one of the position sensor signal circuits may set this DTC. |
| • | An internal short to ground in one of the position sensors may set this DTC. |
Reference Information
Schematic Reference
Connector End View Reference
Electrical Information Reference
Scan Tool Reference
| • | Scan Tool Data List for the power seats |
| • | Scan Tool Data List for the adjustable pedals |
| • | Scan Tool Data Definitions for the power seats |
| • | Scan Tool Data Definitions for the adjustable pedals |
| • | Scan Tool Output Controls for the power seats |
| • | Scan Tool Output Controls for the adjustable pedals |
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at any one of the seat, lumbar, or adjustable pedals position sensors.
- Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit and ground.
| ⇒ | If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the MSM. |
| ⇒ | If greater than the specified range, test the circuits listed below for a short to voltage. If all circuits test normal, replace the MSM. |
| • | 5-volt reference circuit |
| • | The seat, lumbar, and adjustable pedal position sensor signal circuits |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for memory seat module replacement, setup, and programming
