GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2004 🢒 SRX 🢒 Instrument Panel 🢒 Driver Information Center (DIC) 🢒 DIC Vehicle Personalization

Your vehicle is equipped with personalization that allows you to program certain features to a preferred setting for up to two people. The number of programmable features varies depending upon which model of the vehicle is purchased.

On all vehicles, features such as climate control settings, radio preset settings, exterior lighting at unlock, remote lock and unlock confirmation, and automatic door locks have already been programmed for your convenience.

Some vehicles are equipped with additional features that can be programmed including the seat and outside rearview mirror position. The navigation system screen preferences will remain at the last set position.

If your vehicle is equipped with the ability to program additional personalization features, the driver's preferences are recalled by pressing the unlock button on the remote keyless entry transmitter, 1 or 2, or by pressing the appropriate memory button, 1 or 2, located on the driver's door. Certain features can be programmed not to recall until the key is placed in the ignition. To change feature preferences you must use one of the following procedures.

Entering the Personalization Menu

To enter the feature programming mode, use one of the following procedures:

Base Audio System

  1. Turn the ignition to ON, but do not start the engine. Make sure the vehicle is in PARK (P).
  2. If your vehicle has memory settings, press the appropriate memory button, 1 or 2, located on the driver's door armrest. The DIC display will show either Driver 1 or 2 depending on which button was selected.
  3. Press the TUNE/SEL knob once to access the main menu of the DIC.
  4. Turn the TUNE/SEL knob until SETUP is highlighted.
  5. Press the TUNE/SEL knob once to access the SETUP menu.
  6. Scroll to the feature you want to change, and press the TUNE/SEL knob to turn the feature on or off. If the feature is turned on, a check mark will appear next to the feature name.

If none of the personalization items are turned on, turn on the personalization menu by pressing the TUNE/SEL knob. The list of features will then appear, and you can repeat Step 6.

Navigation System

  1. Turn the ignition to ON without the engine running. Make sure the vehicle is in PARK (P).
  2. If your vehicle has memory settings, press the appropriate memory button, 1 or 2, located on the driver's door armrest. The DIC display will show either Driver 1 or 2 depending on which button was selected.
  3. Press the Audio/Adjust button to the left of the screen to enter the Main Audio menu.
  4. Touch the Feature Programming button on the screen.
  5. Scroll to the item you want to change and press the button next to the item to modify the item as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

If none of the personalization items are on, turn on the personalization menu by pressing the ON button next to personalization.

Personalization Features

The following choices are available for programming using both the Base audio and Navigation systems unless otherwise indicated.

Personalization Name

This feature allows you to type in a name that will appear on the DIC display whenever the corresponding remote keyless entry transmitter is used or one of the buttons on the driver's door armrest (1 or 2) is pressed.

If a customized name is not programmed, the system will show Driver 1 or Driver 2 to correspond with the numbers on the back of the remote keyless entry transmitters.

To program a name, use one of the following procedures:

To customize the name using the Base audio system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Select the PERSONALIZATION NAME menu item by pressing the TUNE/SEL knob once.

    3. You will see a cursor on the screen.

  3. Turn the TUNE/SEL knob until you reach the first letter you want; the letter will be highlighted. There is a complete alphabet with both upper and lower case letters and the numbers zero through nine. Also included are spaces and other non-letter characters such as the ampersand (&).
  4. Press the TUNE/SEL knob once to select the letter. The letter will then appear on the display.

    5. If you make a mistake, press the TUNE/SEL knob repeatedly to cycle through all the characters until you reach the character you wish to change.

  5. Repeat Steps 2 and 3 until the name you want is complete. You can program up to 16 characters.

To customize the name using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to the PERSONALIZATION NAME menu item and press the EDIT button next to it.
  3. A keyboard will appear on the screen. Use it to enter the desired name, up to 20 characters.
  4. When you are done entering the name press the ENTER button on the bottom of the screen.

The name you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Configure Display Keys (Base Audio System)

This feature allows you to customize the functions of the four soft keys located to the left and right of the audio display. See "Configurable Radio Display Keys" under Radio with CD for programming information.

Remote Recall Memory/Recall Driving Positions

If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed seat, adjustable pedals and mirror controls when the unlock button on the remote keyless entry transmitter is pressed.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to REMOTE RECALL MEMORY to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to REMOTE RECALL MEMORY and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

    3. If REMOTE RECALL MEMORY is turned on, this will also turn off REMOTE EXIT RECALL and KEY IN RECALL MEMORY if they are not already turned off.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Remote Exit Recall

If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed exit position for the driver's seat when the unlock button on the remote keyless entry transmitter is pressed.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to REMOTE EXIT RECALL to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to REMOTE EXIT RECALL and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

    3. If REMOTE EXIT RECALL is turned on, this will also turn off REMOTE RECALL MEMORY if it is not already turned off.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Key in Recall Memory

If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed seat and mirror positions when the key is inserted into the ignition.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to KEY IN RECALL MEMORY to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to KEY IN RECALL MEMORY and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

    3. If KEY IN RECALL MEMORY is turned on, this will also turn off REMOTE RECALL MEMORY if it is not already turned off.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Auto Exit Seat

If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed exit position for the driver's seat when the key is removed from the ignition and the driver's door is opened.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to AUTO EXIT SEAT using the TUNE/SEL knob to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear in the box next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to AUTO EXIT SEAT and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Twilight Delay

This feature allows you to set the amount of time you want the exterior lamps to remain on after you exit the vehicle.

Programmable Modes

Mode 1: 0:00 seconds

Mode 2: 0:15 seconds

Mode 3: 0:30 seconds

Mode 4: 1:00 minute

Mode 5: 1:30 minutes

Mode 6: 2:00 minutes

Mode 7: 2:30 minutes

Mode 8: 3:00 minutes

Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since the vehicle left the factory. To determine the mode to which the vehicle is programmed or to program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to TWILIGHT DELAY using the TUNE/SEL knob to highlight it.
  3. Press the TUNE/SEL knob to scroll through the available delay settings. When the delay time you want is highlighted, press the TUNE/SEL knob once to select it.

    4. When the mode is turned on, an X will appear in the box to the left.

    If you choose Mode 1, the exterior lamps will not illuminate when you exit the vehicle. Only one mode can be selected at a time.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to TWILIGHT DELAY and press the ADJUST button next to it.
  3. A new screen will appear with the available delay settings. Use the buttons on the screen to adjust the selected delay.
  4. When you are done entering the delay press the RETURN button on the screen.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Lights Flash at Unlock

This feature turns on the exterior lamps when the remote keyless entry transmitter is used to unlock the vehicle. The lamps will remain on for approximately 20 seconds unless a door is opened, the ignition is turned to ACCESSORY, ON or START or the remote keyless entry transmitter is used to lock the vehicle.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to LIGHTS FLASH AT UNLOCK to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to LIGHTS FLASH AT UNLOCK and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Lights Flash at Lock

This feature allows the exterior lamps to flash once when the remote keyless entry transmitter is used to lock the vehicle. All doors must be closed for this feature to work, and the lamps will not flash if the parking lamps or headlamps are on.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to LIGHTS FLASH AT LOCK to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to LIGHTS FLASH AT LOCK and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

You can select this feature by itself, or you can combine it with Horn Sounds At Lock so that both the lights flash and the horn chirps when you lock your vehicle.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Horn Sounds at Lock

This feature sounds the horn once when the remote keyless entry transmitter is used to lock the vehicle. All doors must be closed for this feature to work.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to HORN SOUNDS AT LOCK to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to HORN SOUNDS AT LOCK and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

If you select this feature to be on, Lights Flash At Lock will also be on. You can choose Lights Flash At Lock by itself, but Horn Sounds At Lock will always have Lights Flash At Lock enabled when it is selected.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Exterior Lights at Unlock

This feature turns on the exterior lamps when the remote keyless entry transmitter is used to unlock the vehicle. The lamps will remain on for about 20 seconds unless a door is opened, the ignition is turned to ACCESSORY, ON or START or the remote keyless entry transmitter is used to lock the vehicle.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to EXT. LIGHT AT UNLOCK to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to EXT LIGHTS AT UNLOCK and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Driver Unlock in Park

The feature allows the driver's door to automatically unlock when the transmission is shifted into PARK (P).

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to DRIVER UNLOCK IN PARK to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to DRIVER UNLOCK IN PARK and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

    3. If DRIVER UNLOCK IN PARK is turned on, this will also turn off DRIVER UNLOCK KEY OUT, DOORS UNLOCK IN PARK and DOORS UNLOCK KEY OUT if they are not already turned off.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Driver Unlock Key Out

This feature allows the driver's door to automatically unlock when the key is removed from the ignition.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to DRIVER UNLOCK KEY OUT.
  3. Press the TUNE/SEL knob to switch between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to DRIVER UNLOCK KEY OUT and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

    3. If DRIVER UNLOCK KEY OUT is turned on, this will also turn off DRIVER UNLOCK IN PARK, DOORS UNLOCK IN PARK and DOORS UNLOCK KEY OUT if they are not already turned off.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Doors Unlock in Park

The feature allows the doors to automatically unlock when the transmission is shifted into PARK (P).

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to DOORS UNLOCK IN PARK to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to DOORS UNLOCK IN PARK and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

    3. If DOORS UNLOCK IN PARK is turned on, this will also turn off DRIVER UNLOCK IN PARK, DRIVER UNLOCK KEY OUT and DOORS UNLOCK KEY OUT if they are not already turned off.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Doors Unlock Key Out

This feature allows the doors to automatically unlock when the key is removed from the ignition.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to DOORS UNLOCK KEY OUT.
  3. Press the TUNE/SEL knob to switch between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to DOORS UNLOCK KEY OUT and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

    3. If DOORS UNLOCK KEY OUT is turned on, this will also turn off DRIVER UNLOCK IN PARK, DRIVER UNLOCK KEY OUT and DOORS UNLOCK IN PARK if they are not already turned off.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Delayed Locking

This feature delays the locking of the vehicle's doors for up to five seconds after a power door lock switch or the lock button on the remote keyless entry transmitter is pressed. The five second delay occurs after the last door is closed.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to DELAYED LOCKING using the TUNE/SEL knob to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to DELAYED LOCKING and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Lock Passenger Window

This feature allows you to disable either all the passenger window switches or the rear passenger window switches only. If this feature is turned on, all passenger window switches will be disabled when the window lockout button is pressed. If the feature is off, only the rear passenger window switches will be disabled. See Power Windows for more information.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to LOCK PASS WINDOW using the TUNE/SEL knob to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to LOCK PASS WINDOW and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Mirror to Curb in Reverse

If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, the passenger's outside rearview mirror will move downward so you can view the curb when the shift lever is shifted into REVERSE (R). The mirror will return to the last known driving position when the shift lever is moved out of REVERSE (R). See Outside Curb View Assist Mirror for more information.

Programmable Modes

Mode 1: ON

Mode 2: OFF

Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to MIRROR TO CURB IN REV using the TUNE/SEL knob to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between on and off.

    4. When the mode is turned on, a check mark will appear next to the feature name.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to MIRROR TO CURB IN REVERSE and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Enhanced Chime Volume

This feature allows you to adjust the volume level of the vehicle's warning chimes. The chime volume cannot be turned off, only adjusted.

Programmable Modes

Mode 1: NORMAL

Mode 2: LOUD

Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use one of the following procedures:

To change the mode using the Base audio system, do the following:

  1. Enter the personalization portion of the SETUP menu following the instructions listed previously.
  2. Scroll to ENHANCED CHIME VOLUME using the TUNE/SEL knob to highlight it.
  3. Press the TUNE/SEL knob to switch back and forth between the normal and loud settings.

To change the mode using the Navigation system, do the following:

  1. Enter the Personalization menu by following the instructions listed previously.
  2. Scroll to ENHANCE CHIME VOLUME and press the ON or OFF button next to it as desired. If the item is turned on, the color of the ON button will be light blue. If the item is turned off, the color of the OFF button will be light blue.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

Exiting the Personalization Menu

Once you've finished making your selections on the Base audio system, you will return to the main audio screen.

To exit Feature Programming using the Navigation system, press any of the buttons located next to the screen.