DTC B2106 Horizontal Forward Switch Failed Eldorado
Circuit Description
The memory seat module (MSM) receives an input from the LH seat switch entire seat switch when the switch is actuated. When the entire seat switch is operated in the forward direction, battery positive voltage (B+) is supplied to the MSM entire seat forward input via CKT 1522 (TAN). The MSM recognizes the input and moves the entire seat in the forward direction.
Conditions for Setting the DTC
| • | When the entire seat forward switch is active for 30 seconds after motion has ceased, the switch will be considered shorted and the DTC will set. |
| • | If the horizontal position sensor DTC B2117 is current and the entire seat forward switch is active for 30 seconds, the switch will be considered shorted and the DTC will set. |
| • | DTC B2106 will set only if DTC B1982 MSM or DTC B1983 MSM is not current. |
Action Taken When the DTC Sets
| • | The MSM will not move the entire seat in the forward direction. |
| • | The MSM will continue to respond to valid inputs from the other manual switches. |
| • | All memory recall function commands will be ignored for all directions. |
Conditions for Clearing the DTC
| • | The MSM sees that the entire seat forward switch is no longer active. |
| • | Use the On-Boards clearing DTCs feature. |
| • | Use a scan tool. |
Test Description
The numbers below refer to the step numbers on the diagnostic table:
-
Perform the entire Power Seat Systems Diagnostic System Check before continuing with the diagnosis of this DTC.
-
Determines whether there is a stuck switch or a short to battery positive voltage (B+) in the wiring input to the memory seat module (MSM). DTC B2106 will set again if there is a short in the wiring or there is an internal MSM problem. DTC B2106 will not set again if there is a stuck switch because the switch has been disconnected from the memory seat module (MSM) input.
-
Determines whether there is a short to battery positive voltage (B+) in the input wiring to the MSM.
-
Clear all DTCs after the repair procedure is complete.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Was the entire Power Seat Systems Diagnostic System Check performed? | -- | |||
After 30 seconds, does DTC B2106 reset? | -- | |||
Is the voltage within the specified range? | 10-15 V | |||
4 | Replace the memory seat module (MSM). Refer to Memory Seat Control Module Replacement . Is the MSM replacement complete? | -- | -- | |
5 | Replace the LH seat switch. Refer to Power Seat Switch Replacement . Is the LH seat switch replacement complete? | -- | -- | |
6 | Repair the short to battery positive voltage (B+) in CKT 1522 (TAN). Refer to Wiring Repairs in Wiring Systems. Is the circuit repair complete? | -- | -- | |
Are all DTCs cleared? | -- | -- |
DTC B2106 Horizontal Forward Switch Failed DeVille
Circuit Description
The memory seat module (MSM) receives an input from the left seat switch entire seat switch when the switch is actuated. When the entire seat switch is operated in the forward direction, battery positive voltage (B+) is supplied to the MSM entire seat forward input via CKT 613 (GRY). The MSM recognizes the input and moves the entire seat in the forward direction.
Conditions for Setting the DTC
| • | When the entire seat forward switch is active for 30 seconds after motion has ceased, the switch is considered shorted and the DTC sets. |
| • | If the seat horizontal position sensor DTC B2117 is current and the entire seat forward switch is active for 30 seconds, the switch is considered shorted and the DTC sets. |
| • | DTC B2106 sets only if DTC B1982 MSM or DTC B1983 MSM is not current. |
Action Taken When the DTC Sets
| • | The MSM does not move the entire seat in the forward direction. |
| • | The MSM continues responding to valid inputs from the other manual switches. |
| • | All memory recall function commands are ignored for all directions. |
Conditions for Clearing the DTC
| • | The MSM sees that the entire seat forward switch is no longer active. |
| • | Use the on-boards clearing DTCs feature. |
| • | Use a scan tool. |
Test Description
The numbers below refer to the step numbers on the diagnostic table:
-
Perform the entire Power Seat Systems Diagnostic System Check before continuing with the diagnosis of this DTC.
-
Determines whether there is a stuck switch or a short to battery positive voltage (B+) in the wiring input to the memory seat module (MSM). DTC B2106 will set again if there is a short in the wiring or there is an internal MSM problem. DTC B2106 will not set again if there is a stuck switch because the switch has been disconnected from the memory seat module (MSM) input.
-
Determines whether there is a short to battery positive voltage (B+) in the input wiring to the MSM.
-
Clear all DTCs after the repair procedure is complete.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Was the entire Power Seat Systems Diagnostic System Check performed? | -- | |||
After 30 seconds, does DTC B2106 reset? | -- | |||
Is the voltage within the specified range? | 10-15 V | |||
4 | Replace the memory seat module (MSM). Refer to Memory Seat Control Module Replacement . Is the MSM replacement complete? | -- | -- | |
5 | Replace the LH seat switch. Refer to Power Seat Switch Replacement . Is the LH seat switch replacement complete? | -- | -- | |
6 | Repair the short to battery positive voltage (B+) in CKT 613 (GRY). Refer to Wiring Repairs in Wiring Systems. Is the circuit repair complete? | -- | -- | |
Are all DTCs cleared? | -- | -- |
