Radio Front Side Door Speaker Replacement DeVille

1. Remove the door trim panel. Refer to Front Side Door Trim Panel Replacement in Doors.



2. Remove the fasteners in order to release the 15 cm (5.25 in) speaker (1).
3. Partially remove the speaker.
4. Disconnect the electrical connector.
5. Remove the speaker.

1. Partially install the speaker.
2. Connect the electrical connector.
3. Align the speaker to the door.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the fasteners in order to attach the 15 cm (5.25 in) speaker (1).

Tighten
Tighten the fasteners to 2 N·m (18 lb in)

5. Install the door trim panel. Refer to Front Side Door Trim Panel Replacement in Doors.

Radio Front Side Door Speaker Replacement Eldorado with UW6

1. Remove the door trim panel. Refer to Door Trim Panel Replacement in Doors.



2. Disconnect the speaker electrical connector (1).
3. Remove the 3 fasteners in order to release the speaker unit (4).

The enclosure contains the following components:

•	The tweeter speaker (3)

•	The midrange speaker (2)

4. Remove the tweeter speaker (3) and the midrange speaker (2).

The following components hold both the tweeter speaker (3) and the midrange speaker (2) in place inside the enclosure:

•	Four fasteners

•	Two electrical connections

1. Install the tweeter speaker (3) and/or the midrange speaker (2), if removed. Use 4  fasteners each.

Route the wire through the notches in the housing in order to prevent damage.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the 3 fasteners in order to attach the enclosure to the door.

Tighten
Tighten the fasteners to 2 N·m (18 lb in).

3. Connect the speaker electrical connectors (1).
4. Install the door trim panel. Refer to Door Trim Panel Replacement in Doors.

Radio Front Side Door Speaker Replacement Eldorado with UQ4

1. Remove the door trim panel. Refer to Door Trim Panel Replacement in Doors.
2. Disconnect the speaker electrical connector.
3. Remove the 3 fasteners in order to release the speaker unit.

The enclosure contains an amplifier and a speaker.




4. Remove the following components:

•	The grille

•	The speaker (3)

•	The gasket

•	The amplifier cover (1)

•	The gasket (5)

5. Remove the amplifier (4).
6. Disconnect the harness connector (2).

1. Install the following components:

•	Install the amplifier (4).

•	Connect the harness connector.

•	The gasket (5)

•	Properly reposition the gaskets in order to achieve proper performance. Route the harnesses through the notches in the housing in order to prevent damage.

•	The amplifier cover (1).

•	Install the fasteners.

•	The gasket.

•	The speaker (3).

•	Install the fasteners.

•	The grille.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the 3 fasteners in order to reattach the enclosure to the door.

Tighten
Tighten the fasteners to 2 N·m (18 lb in).

3. Connect the electrical connector.
4. Install the door trim panel. Refer to Door Trim Panel Replacement in Doors.