GM Service Manual Online
For 1990-2009 cars only

Radio Replacement Eldorado and DeVille with D55

Removal Procedure

  1. Remove the console trim plate. Refer to Console Front Trim Plate Replacement in Instrument Panel, Gauges and Console.
  2. Remove the ashtray assembly. Refer to Ashtray Replacement in Instrument Panel, Gauges and Console.
  3. Remove the Driver Information Center Switch (DIS). Refer to Driver Information Display Switch Replacement in Instrument Panel, Gauges and Console.

  4. Object Number: 309002  Size: SH
  5. Remove the fasteners (1) from the radio and heater/AC control assembly.

  6. Object Number: 309004  Size: SH
  7. Disconnect the following components:
  8. • The electrical connectors (1,2,3)
    • The antenna coax cable (4)
  9. Remove the radio and heater/AC control assembly.

  10. Object Number: 493861  Size: SH
  11. If you are using an exchange radio, perform the following additional steps:
  12. 7.1. Remove the bracket fasteners (3).
    7.2. Remove 2 brackets (2) from the sides of the radio and the control assembly.
    7.3. Remove one 16-mm (0.63-in) plastic locating pin and clip stud from the rear of the radio.
    7.4. Remove the driver information display switch bracket (1).

Installation Procedure


    Object Number: 493861  Size: SH
  1. If you are using an exchange radio, perform the following additional steps:
  2. 1.1. Install the driver information display switch bracket (1).
    1.2. Install one 16-mm (0.63-in) plastic locating pin and clip stud to the rear of the radio.
    1.3. Install 2 brackets (2) to the sides of the radio and heater/AC control assembly.

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    1.4. Install the mounting bracket fasteners (3).

    Tighten
    Tighten the fasteners to 6 N·m (53 lb in).


    Object Number: 309004  Size: SH
  3. Connect the electrical connectors (1,2,3).
  4. Connect the antenna coax cable (4).

  5. Object Number: 309002  Size: SH
  6. Install the radio and heater/AC control assembly to the IP.
  7. Install the fasteners (1).
  8. Tighten
    Tighten the fasteners to 2 N·m (18 lb in).

  9. Install the DIS into the console opening. Refer to Driver Information Display Switch Replacement in Instrument Panel, Gauges and Console.
  10. Install the ashtray. Refer to Ashtray Replacement in Instrument Panel, Gauges and Console.
  11. Install the console trim plate. Refer to Console Front Trim Plate Replacement in Instrument Panel, Gauges and Console.

Radio Replacement Deville without D55

Removal Procedure

  1. Remove the radio trim plate. Refer to Instrument Panel Lower Center Trim Replacement in Instrument Panel, Gauges and Console.

  2. Object Number: 309015  Size: MH
  3. Push inward on the tabs (2) on the side of the radio.
  4. Pull out the radio.

  5. Remove the radio.
  6. Disconnect the following components:
  7. • The coax cable (4)
    • The electrical connector (1)
    • Remove the radio.

    Object Number: 309040  Size: SH
  8. If using an exchange radio, perform the following additional steps:
  9. 5.1. Remove the fasteners (2) retaining the brackets (1) to the radio.
    5.2. Remove 2 brackets (1) from the sides of the radio.
    5.3. Remove one 16 mm (0.63 in) plastic locating pin and clip stud from the rear of the radio.

Installation Procedure


    Object Number: 309040  Size: SH
  1. If using an exchange radio, perform the following additional steps:
  2. 1.1. Install one 16 mm (0.63 in) plastic locating pin and clip stud to the rear of the radio.
    1.2. Install 2 brackets (1) to the sides of the radio.

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    1.3. Install the mounting bracket fasteners.

    Tighten
    Tighten the fasteners to 5 N·m (44 lb in).


    Object Number: 309015  Size: MH
  3. Connect the following components:
  4. • The radio electrical connector (1)
    • The antenna coax cable (4)
  5. Guide the radio into the instrument panel.
  6. Align the pin on the rear of the radio.

    Push in the pin until the lock tabs catch.

  7. Install the radio trim plate. Refer to Instrument Panel Lower Center Trim Replacement in Instrument Panel, Gauges and Console.