Fuel Tank Filler Door Lock Actuator Replacement DeVille

1. Remove the nut retaining the latch from the pocket.
2. Remove the rear compartment trim. Refer to Rear Compartment Trim Panel Replacement or to Rear Compartment Trim Panel Replacement .



3. Remove the grommet and latch (1) from the wheelhouse.
4. Remove the bolts (2).
5. Disconnect the wire connector from the actuator (4).
6. Remove the fuel filler door release actuator (4).

1. Install the latch and grommet (1) through the hole in the wheelhouse.

Align the latch with the rib on the fuel pocket.

2. Install the nut in order to retain the latch (1) to the pocket.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Adjust the latch (1) in order to bring the door flush with the body.

Tighten
Tighten the nut to 3 N·m (26.5 lb in).

4. Install the fuel filler door release actuator (4) to the bracket.
5. Attach the actuator (4) to the latch (1).
6. Install the bolts (2).

Tighten
Tighten the bolts to 6 N·m (53 lb in).

7. Connect the wire connector to the actuator (4).

Important: The manual release handle of the fuel filler door must be visible in the cargo area through the slit in the rear compartment trim.

8. Install the rear compartment trim. Refer to Rear Compartment Trim Panel Replacement or to Rear Compartment Trim Panel Replacement .

Fuel Tank Filler Door Lock Actuator Replacement Eldorado

1. Remove the nut retaining the latch from the pocket.
2. Remove the rear compartment trim. Refer to Rear Compartment Trim Panel Replacement or to Rear Compartment Trim Panel Replacement .



3. Remove the grommet and latch (1) from the wheelhouse.
4. Remove the bolts (2).
5. Disconnect the wire connector from the actuator (4).
6. Remove the fuel filler door release actuator (4).

1. Install the latch and grommet (1) through the hole in the wheelhouse.

Align the latch with the rib on the fuel pocket.

2. Install the nut in order to retain the latch (1) to the pocket.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Adjust the latch (1) in order to bring the door flush with the body.

Tighten
Tighten the nut to 3 N·m (26.5 lb in).

4. Install the fuel filler door release actuator (4) to the bracket.
5. Attach the actuator (4) to the latch (1).
6. Install the bolts (2).

Tighten
Tighten the bolts to 6 N·m (53 lb in).

7. Connect the wire connector to the actuator (4).

Important: The manual release handle of the fuel filler door must be visible in the cargo area through the slit in the rear compartment trim.

8. Install the rear compartment trim. Refer to Rear Compartment Trim Panel Replacement or to Rear Compartment Trim Panel Replacement .