Product Enhancement for Inventory and Customer Vehicles-Radio Inoperative/Battery Drain-Expires with Base Warranty

THIS PRODUCT ENHANCEMENT INCLUDES VEHICLES IN DEALER INVENTORY AND CUSTOMER VEHICLES THAT RETURN FOR ANY TYPE OF SERVICE, AND WILL EXPIRE AT THE END OF THE INVOLVED VEHICLE'S NEW VEHICLE LIMITED WARRANTY PERIOD.

This bulletin provides a service procedure to reprogram the radio. These vehicles may have a condition where the radio will not function or turn off, possibly resulting in a dead battery.

This service procedure should be completed as soon as possible on involved vehicles currently in dealer inventory and customer vehicles that return to the dealer for any type of service during the New Vehicle Limited Warranty coverage period.

A list of involved vehicles currently in dealer inventory is attached to the Administrative Message (US) or Dealer Communication (Canada) used to release this bulletin. Customer vehicles that return for service, for any reason, and are still covered under the vehicle's base warranty, and are within the VIN breakpoints provided below, should be checked for vehicle eligibility in the appropriate system listed below.

Important: Dealers are to confirm vehicle eligibility prior to beginning repairs by using GMVIS. Not all vehicles within the above breakpoints may be involved.

Tech 2® Remote Programming Method for Radio (RAD)

Important: The calibration numbers required for this service procedure are programmed into control modules via a Techline Tech 2® scan tool and the Techline Information System (TIS) 2000 terminal with the calibration update. Use data version 11.0 for 2006 or later, broadcast to dealers on October 28, 2006 (in Canada, October 30, 2006), or TIS 2 Web version 10.5 for 2006 (website version of TIS), and on TIS DVD version 11.0/2006 or later, that was mailed to dealers in November 2006. If you cannot access the calibration, call the Techline Customer Support Center at 1-800-828-6860 (English) or 1-800-503-3222 (French) and it will be provided.

Notice: Before reprogramming, please check the battery condition to prevent a reprogramming error of any of the modules due to battery discharge. Battery voltage must be between 12 and 16 volts during reprogramming. If the vehicle battery is not fully charged, use jumper cables from an additional battery. Be sure to turn off or disable any system that may put a load on the battery, such as automatic headlamps, daytime running lights, interior lights, heating, ventilation, and air conditioning (HVAC) system, radio, engine cooling fan, etc. A programming failure or control module damage may occur if battery voltage guidelines are not observed.

The ignition switch must be in the proper position. The Tech 2® prompts you to turn ON the ignition, with the engine OFF. DO NOT change the position of the ignition switch during the programming procedure, unless instructed to do so.

Make certain all tool connections are secure, including the following components and circuits:

DO NOT disturb the tool harnesses while programming. If an interruption occurs during the programming procedure, programming failure or control module damage may occur.

DO NOT turn OFF the ignition if the programming procedure is interrupted or unsuccessful. Ensure that all control module and DLC connections are secure and the TIS terminal operating software is up to date.

1. Verify the battery charge of 12 to 16 volts. The battery must be able to maintain the charge during programming. Use an additional jump battery if necessary.
2. Use the normal "request method" through "Service Programming System" to request information from the vehicle.
3. At the Techline Terminal, enter TIS SPS programming system.
4. Select Tech 2® from the "Select Diagnostic Tool" window.
5. Select Replace and Program from the "Select Programming Process" window.
6. Select Vehicle from the "Select ECU Location" window.
7. Select Next to go to the "Preparing for Communication" instruction screen.
8. Select Next to view the "Validate Vehicle ID Number" screen. If the vehicle ID number does not appear on the screen, manually insert the VIN into the VIN window of the "Validate Vehicle ID Number" screen.
9. Select Next to view the "Supported Controllers" screen.

Important: Verify the radio type in GMVIS: RPO US8/US9 + UQ3, MP3 radio with enhanced speakers or RPO US8/US9 + UQA, MP3 radio with premium speakers.

10. Select Radio (RAD) from "Supported Controllers" window. Select the vehicle specific radio from "Supported Controllers" Window.
11. Select Next to view the "Select Programming Type" window.
12. Select Normal from the "Select Programming Type" window.
13. Select Next to view the "Service Programming System Calibration Selection" screen.
14. Select Next to view "Summary" screen.
15. Verify that current and selected calibration information is displayed on the "Summary" screen.
16. Select Next to download the calibration to the Tech 2®.
17. Back at the vehicle, enter "Service Programming Systems".
18. Select Program ECU and follow the on-screen instructions.
19. When programming is complete, do the following:

19.1.

Turn the Tech 2® OFF.

19.2.

Turn the ignition switch OFF.

20. Wait 30 seconds.
21. Turn the ignition switch to ON with the engine OFF.
22. Go into Diagnostics and check for DTC codes.
23. Clear all codes.