This vehicle is equipped with advanced diagnostic capabilities. The OBD II system is a much more complex system than the prior on-board diagnostics. The engine control module (ECM) interacts with many more emission related components and systems, and monitors emission related components and systems for deterioration. Most of these diagnostics will detect a problem before the customer notices a change in the driveability. OBD II diagnostics monitor the system performance and a diagnostic trouble code (DTC) will set if the system performance degrades.
The malfunction indicator lamp (MIL) operation and the DTC storage are dictated by the DTC type. A DTC is ranked as a Type A or Type B if the DTC is emissions related. Type C is not emissions related. Each DTC type has its own set of MIL operation, DTC storage, and a DTC clearing criteria.
The ECM is in the engine compartment, inside the relay center. The ECM is the control center of the engine controls system. The ECM controls the following components:
• | The fuel injection system |
• | The ignition system |
• | The emission control systems |
• | The on-board diagnostics for engine functions |
• | The A/C and multi-ram systems |
• | The throttle actuation control (TAC) system |
The ECM constantly looks at the information from various sensors and other inputs, and controls the systems that affect the vehicle performance and the emissions. The ECM also performs diagnostic tests on various parts of the system. The ECM can recognize operational problems and alert the driver via the MIL. When the ECM detects a malfunction, the ECM stores a DTC. The problem area is identified by the particular DTC that is set. This aids the technician in making repairs.
The ECM connects to the engine wiring harness by two 64-pin connectors.
The ECM can supply 5 volts or 12 volts to the various sensors or switches. This is done through pull-up resistors to the regulated power supplies within the ECM. In some cases, even an ordinary shop voltmeter will not give an accurate reading because the resistance is too low. Therefore, a DMM with at least 10 megaohms input impedance is required in order to ensure accurate voltage readings.
The ECM controls the output circuits such as the injectors, the relays, the IAC, etc. by controlling the ground or the power feed circuit through the transistors or a device called an output driver module.
The electronically erasable programmable read only memory (EEPROM) is a permanent memory that is physically part of the ECM. The EEPROM is not a removable component. The EEPROM contains program and calibration information that the ECM needs in order to control the powertrain operation.
Unlike the programmable read only memory (PROM) used in the past applications, the EEPROM is not replaceable. Special equipment, as well as the correct program and calibration for the vehicle, are required in order to reprogram the ECM.
This vehicle is equipped with a theft deterrent system which interfaces with the ECM. If the ECM is replaced, program the new ECM with the frequency code of the theft deterrent module that is currently on the vehicle. The vehicle will not start until this procedure is completed.
The ECM employs an internal integrated circuit to continuously monitor the knock control evaluation circuit. The KS module contains the circuitry that allows the ECM to utilize the knock sensor (KS) signals and diagnose the KS sensors and circuitry. The KS module is not a replaceable component. If the ECM detects a fault in the ability of the KS module to sample these signals, a DTC will set.
The data link connector (DLC) is a 16-pin connector that provides the technician a means of accessing serial data for aid in the diagnosis. This connector allows the technician to use a scan tool in order to monitor the various serial data, parameters, and display the DTC information. The DLC is located inside of the drivers compartment, underneath the dash. Pin-4 and pin-5 are grounds. Pin-7 is the ISO serial data. Pin-16 is B+.
The Catera uses ISO serial data and communicates with the scan tool on DLC pin-7. Most other GM OBD II vehicles use class 2 serial data on DLC pin-2. Both the ECM and the transmission control module (TCM) communicate with the scan tool by using the ISO serial data circuit.
The MIL is inside of the instrument panel cluster (IPC). The MIL is controlled by the ECM and illuminates when the ECM has detected a problem that affects the vehicle emissions.
The ECM, by design, can withstand the normal current draws that are associated with the vehicle operations. However, care must be used in order to avoid overloading any of these circuits. When testing for opens or shorts, do not ground or apply voltage to any of the ECM circuits unless the diagnostic procedure instructs you to do so. These circuits should only be tested with a digital multimeter (DMM).
This OBD II equipped vehicle is designed to self-diagnose any conditions that could lead to excessive levels of the following emissions:
• | Hydrocarbons (HC) |
• | Carbon monoxide (CO) |
• | Oxides of nitrogen (NOx) |
• | Evaporative emission (EVAP) system losses |
Should this vehicles on-board diagnostic system (ECM) detect a condition that could result in excessive emissions, the ECM turns ON the MIL and stores a DTC that is associated with the condition. Always begin the diagnosis with the Diagnostic System Check-Engine Controls when diagnosing a condition reported from a state I/M program.
Additional information on the on-board diagnostic system I/M ready status and drive cycle appears later in this section.
Notice: Do not attach add-on vacuum operated equipment to this vehicle. The use of add-on vacuum equipment may result in damage to vehicle components or systems.
Notice: Connect any add-on electrically operated equipment to the vehicle's electrical system at the battery (power and ground) in order to prevent damage to the vehicle.
Aftermarket, add-on, electrical and vacuum equipment is defined as any equipment installed on a vehicle after leaving the factory that connects to the vehicles electrical or vacuum systems. No allowances have been made in the vehicle design for this type of equipment.
Add-on electrical equipment, even when installed to these strict guidelines, may still cause the powertrain system to malfunction. This may also include equipment not connected to the vehicle electrical system, such as portable telephones and radios. Therefore, the first step in diagnosing any powertrain problem is to eliminate all of the aftermarket electrical equipment from the vehicle. After this is done, if the problem still exists, the problem may be diagnosed in the normal manner.
Important: In order to prevent possible electrostatic discharge damage to the ECM, DO NOT touch the connector pins on the ECM.
The electronic components that are used in the control systems are often designed to carry very low voltage. The electronic components are susceptible to damage caused by electrostatic discharge. Less than 100 volts of static electricity can cause damage to some electronic components. By comparison, it takes as much as 4,000 volts for a person to even feel the zap of a static discharge.
There are several ways for a person to become statically charged. The most common methods of charging are by friction and by induction. An example of charging by friction is a person sliding across a car seat.
Charging by induction occurs when a person with well insulated shoes stands near a highly charged object and momentarily touches ground. Charges of the same polarity are drained off leaving the person highly charged with the opposite polarity. Static charges can cause damage, therefore, it is important to use care when handling and testing electronic components.
The underhood Vehicle Emissions Control Information Label contains important emission specifications and setting procedures. In the upper left corner is the exhaust emission information. This identifies the year, the manufacturing division of the engine, the displacement of the engine in liters, the class of the vehicle, and type of fuel metering system. There is also an illustrated emission components and vacuum hose schematic.
This label is located in the engine compartment of every General Motors vehicle. If the label has been removed, it can be ordered from GM service parts operations (GMSPO).
Refer to the Maintenance Schedule in Maintenance and Lubrication for the maintenance that should be performed to retain the emission control performance.
Important: This visual and physical inspection is very important and must be done carefully and thoroughly.
Perform a careful visual and physical underhood inspection when performing any diagnostic procedure or diagnosing the cause of an emission test failure. This can often lead to repairing a problem without further steps. Use the following guidelines when performing a visual and physical inspection:
• | Inspect all of the vacuum hoses for correct routing, pinches, cuts, or disconnects. |
• | Inspect any hoses that are difficult to see beneath the air cleaner, the A/C compressor, the generator, etc. |
• | Inspect all of the wires in the engine compartment for the following conditions: |
- | Burned or chafed spots |
- | Pinched wires |
- | Contact with sharp edges |
- | Contact with hot exhaust manifolds |
Notice: Lack of basic knowledge of this powertrain when performing diagnostic procedures could result in incorrect diagnostic performance or damage to powertrain components. Do not attempt to diagnose a powertrain problem without this basic knowledge.
A basic understanding of hand tools is necessary in order to effectively use this section of the Service Manual.
You must be familiar with some of the basics of engine operation and electrical diagnosis in order to use this section of the service manual.
• | Basic electrical circuits--You should have an understanding of basic electricity and know the meaning of voltage (volts), current (amps), and resistance (ohms). You should understand what happens in a circuit with an open or a shorted wire, and you should be able to identify a shorted or open circuit by using a DMM. You should be able to read and understand a wiring diagram. |
• | Use of digital multimeter--You should be familiar with the digital multimeter (DMM), particularly the essential tool . You should be able to use the meter in order to measure the voltage (volts), the resistance (ohms), the current (amps), intermittents (min/max), and frequency (Hertz). |
• | Use of circuit testing tools--You should not use a test lamp to diagnose the engine controls system unless you are specifically instructed to do so. You should know how to the use jumper wires in order to test the components and allow the DMM readings without damaging the terminals. You should know how to use the J 35616 connector test adapter kit and use the kit whenever the diagnostic procedures call for front probing any connector. |