Was the Rear Sunshade System Check performed?

--

Go to Step 2

Go to Rear Sunshade System Check

Lower or raise the RH power window from the RH power window switch.

Did the window lower or raise properly?

--

Go to Step 3

Go to Power Windows System Check

Remove and inspect the 30 amp HTD SEAT REAR fuse.

Is the fuse open?

--

Go to Step 4

Go to Step 5

Test the battery feed circuit to the rear sunshade module for a short to ground. Refer to Testing for Short to Ground in Wiring Systems.

Did you find and correct the condition?

--

Go to LINK

--

1. Disconnect connector C403.
2. Measure the voltage at terminal 3 (RED).

Is the measured voltage within the specified value?

10-12 V

Go to Step 6

Go to Step 7

Remeasure the voltage again, but connect the black DMM lead to terminal 1 (BLK).

Is the measured voltage within the specified value?

10-12 V

Go to Step 8

Go to Step 9

Locate and repair the open battery feed circuit (CKT A95).

Is the repair complete?

--

Go to Step 14

--

Measure the voltage at terminal 2 (BLU/RED) while sliding the sunshade switch rearward.

Is the measured voltage within the specified value?

10-12 V

Go to Step 10

Go to Step 11

Locate and repair the open ground circuit.

Is the repair complete?

--

Go to Step 14

--

1. Reconnect connector C403.
2. Disconnect connector C1 from the sunshade module.
3. Measure for voltage at connector C1 terminal 2 (RED).

Is the measured voltage within the specified value?

10-12 V

Go to Step 12

Go to Step 13

1. Remove the gear selector boot and the center console trim to gain access to the RH power window switch connector.
2. Measure for voltage at the switch connector terminal 1 (BLU/RED) while sliding the sunshade switch rearward.

Is the measured voltage within the specified value?

10-12 V

Go to Step 15

Go to Step 16

Remeasure the voltage again, but connect the DMM black lead to terminal 1 of connector C1.

Is the measured voltage within the specified value?

10-12 V

Go to Step 17

Go to Step 18

Locate and repair the open battery feed circuit in the jumper harness.

Is the repair complete?

--

Go to Step 14

--

Verify that the rear sunshade operates properly.

Does the rear sunshade operate properly?

--

System OK

--

Locate and repair the open or excessive resistance in CKT PA6 (BLU/RED).

Is the repair complete?

--

Go to Step 14

--

Replace the RH power window switch.

Is the replacement complete?

--

Go to Step 14

--

Measure the voltage at connector C1 terminal 3 (BLU/RED) while sliding the sunshade switch rearward.

Is the measured voltage within the specified value?

10-12 V

Go to Step 19

Go to Step 20

Locate and repair the open ground circuit in the jumper harness.

Is the repair complete?

--

Go to Step 14

--

1. Reconnect connector C1 to the module.
2. Disconnect connector C2 from the module.
3. Connect the DMM leads across both of the module terminals where C2 was connected.
4. Slide the sunshade switch rearward and monitor the voltage reading.

Did the voltage measure between 10-12 V and was a click heard inside the module?

--

Go to Step 21

Go to Step 22

Locate and repair the open sunshade signal circuit in the jumper harness.

Is the repair complete?

--

Go to Step 14

--

Replace the sunshade motor.

Is the replacement complete?

--

Go to Step 14

--

Replace the sunshade module.

Is the replacement complete?

--

Go to Step 14

--