Circuit Description
When the ignition switch is turned to the ON position, the inflatable restraint sensing and diagnostic and seat belt pretensioner module (SDM) performs tests to diagnose critical malfunctions within itself. The SDM monitors the six deployment loops to detect leakage currents to ground in the frontal air bag deployment loops, the side air bag deployment loops and the seat belt pretensioner deployment loops. Then, the SDM proceeds with the RESISTANCE MEASUREMENT test to measure the deployment loop resistances to ensure they are within their respective normal resistance ranges. Upon passing these tests, the energy reserve is charged and the firing transistors are tested. The SDM then goes into CONTINUOUS MONITORING mode. The SDM service wait time is 1 minute. Refer to ENABLE/DISABLE procedures.
Conditions for Setting the DTC
DTC 74 will set when the following conditions are met:
| • | The ignition is within normal operating voltage range. |
| • | The measured leakage currents to ground in the driver side impact sensor (SIS) loop are above a specified value caused by a short to ground in the driver side impact sensor (SIS) loop. |
The driver side impact sensor (SIS) loop consists of the following:
| • | Inflatable restraint side impact sensor (SIS) (LH) . |
| • | Harness wiring of CKT B41. |
| • | Harness wiring of CKT B42. |
| • | Harness wiring of CKT XB42. |
| • | Connector terminal contact. |
Action Taken When the DTC Sets
| • | The SDM sets a DTC 74. |
| • | The SDM turns ON the AIR BAG warning lamp. |
Conditions for Clearing the DTC
Current and History DTC codes must be cleared using a scan tool Clear DTC Information command. If the circuit fault has been successfully repaired and the conditions which caused the Current DTC 74 to set are no longer existing, History DTC 74 will set. History DTC 74 may be cleared using the scan tool.
Diagnostic Aids
An inflatable restraint driver side impact sensor (SIS) circuit short to ground can cause an intermittent condition. Inspect CKT B41, CKT B42 and CKT XB42 carefully for cutting and/or chafing. A careful inspection of the circuits and components indicated on the DTC 74 table is essential to make sure that the replacement SDM will not be damaged.
Test Description
The following numbers refer to the step numbers on the diagnostic table:
-
This step checks the inflatable restraint side impact sensor (LH) wiring harness connector for damaged terminals or corrosion.
-
This step checks the inflatable restraint side impact sensor (LH) for damaged terminals or corrosion.
-
This step checks terminal 41 and terminal 42 of the SDM wiring harness connector for damaged terminals or corrosion.
-
This step checks terminal 41 and terminal 42 of the SDM for damaged terminals or corrosion.
-
This step checks for a short to ground in CKT B41 or CKT B42.
-
This step checks for a short to ground in CKT XB42.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the SIR Diagnostic System Check performed? | -- | ||
Is the inflatable restraint side impact sensor (LH) wiring harness connector damaged or corroded? | -- | |||
3 | Use the J 42250 Catera Terminal Repair Kit to repair the inflatable restraint side impact sensor (LH) wiring harness connector. Is the repair complete? | -- | -- | |
Inspect the inflatable restraint side impact sensor (LH) for damaged terminals or corrosion. Is the inflatable restraint side impact sensor (LH) damaged or corroded? | -- | |||
5 | Replace the inflatable restraint side impact sensor (LH). Refer to Inflatable Restraint Side Impact Sensor Replacement . Is the repair complete? | -- | -- | |
Is terminal 41 or terminal 42 of the SDM wiring harness connector damaged or corroded? | -- | |||
7 | Use the J 42250 Catera Terminal Repair Kit to repair the inflatable restraint side impact sensor (LH) wiring harness connector. Is the repair complete? | -- | -- | |
Inspect terminal 41 and terminal 42 of the SDM for damaged terminals or corrosion. Is terminal 41 or terminal 42 of the SDM damaged or corroded? | -- | |||
9 | Replace the SDM. Refer to Inflatable Restraint Sensing and Diagnostic and Seat Belt Pretensioner Module Replacement . Is the repair complete? | -- | -- | |
Use the J 39200 to measure the resistance between terminal 41 of the SDM wiring harness connector and a known good ground. Is the measured resistance less than the specified value? | OL | |||
11 |
Is the repair complete? | -- | -- | |
Use the J 39200 to measure the resistance between terminal 42 of the SDM wiring harness connector and a known good ground. Is the measured resistance less than the specified value? | OL | |||
13 |
Is the repair complete? | -- | -- | |
14 |
Is the repair complete? | -- | -- | |
15 |
Is DTC 74 present? | -- | ||
16 | Reconnect all the SIR components, making sure all the components are properly mounted. Have all the SIR components been reconnected and properly mounted? | -- | -- | |
17 | Use the scan tool to clear all current and history SIR DTCs. Have all current and history SIR DTCs been cleared? | -- | -- |
