Circuit Description
The inflatable restraint Sensing and Diagnostic and Seat Belt Pretensioner Module (SDM) performs tests to diagnose critical malfunctions within itself when the ignition switch is turned ON. The SDM monitors the six firing loops to detect leakage currents to ground in the frontal and side air bag inflator module and seat belt pretensioner circuits. The deployment loop resistances are measured to ensure they are within their respective normal resistance ranges. The SDM service wait time is 1 minute. Refer to On-Vehicle Service for enable/disable procedures.
Conditions for Setting the DTC
The passenger side air bag deployment loop resistance is greater than 4.4 ohms. The passenger side air bag deployment loop consists of the following components:
| • | Inflatable restraint passenger seat module. |
| • | Harness wiring of CKT AM13. |
| • | Harness wiring of CKT XM14. |
| • | Connector terminal contacts, including shorting bars. |
The deployment loop resistance test checks for this malfunction.
Action Taken When the DTC Sets
| • | The SDM sets a Diagnostic Trouble Code. |
| • | The SDM turns ON the AIR BAG warning lamp. |
Conditions for Clearing the DTC
Current and History DTC codes must be cleared using a scan tool Clear DTC Information command. If the circuit fault has been successfully repaired and the conditions which caused the DTC to set are no longer existing, the DTC may be cleared using the scan tool. If the resistance in the inflatable restraint passenger seat module circuit is less than 4.4 ohms, a Current DTC 87 will change to a History DTC 87, which may be cleared using the scan tool.
Diagnostic Aids
A poor connection can cause an intermittent condition. Check the following for a poor connection:
| • | The inflatable restraint passenger seat module integral 2-way connector. |
| • | The inflatable restraint passenger seat yellow 2-way connector. |
| • | The SDM terminals 13 and 14. |
| • | The wire to terminal connections in CKT AM13. |
| • | The wire to terminal connections in CKT XM14. |
Inspect CKTs AM13 and XM14 carefully for cutting and/or chafing. The diagnostic table directs the technician to note the value of RH SIDE AIR BAG RESIST. Comparing the value of RH SIDE AIR BAG RESIST. over multiple ignition cycles can be helpful in determining if an intermittent condition exists.
When measurements are requested in this table, use J 39200 Digital Multimeter with the correct terminal adapter from J 35616 Connector Test Adapter Kit. When a check for proper connection is requested, refer to Intermittents and Poor Connections . When a wire, connector or terminal repair is requested, use J-38125 Terminal Repair Kit and refer to Wiring Repair .
Test Description
The following numbers refer to the step numbers on the diganostic table:
-
This test determines the deployment loop resistance measured by the inflatable restraint Sensing and Diagnostic and Seat Belt Pretensioner Module (SDM).
-
This test isolates the malfunction to one side of the inflatable restraint passenger seat module 2-way yellow integral harness connector.
-
This test isolates the malfunction to one side of the inflatable restraint passenger seat harness located under the RH front seat track cover.
-
This test determines whether the malfunction is in CKT AM13
-
This test determines whether the malfunction is in CKT XM14.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the SIR Diagnostic Check performed? | -- | ||
Has RH SIDE AIR BAG RESIST. been read and recorded on the repair order? | -- | -- | ||
Is RH SIDE AIR BAG RESIST. more than the specified value? | 4.4 ohms | |||
4 | Replace the inflatable restraint passenger seat module. Refer to Inflatable Restraint Seat Module Replacement - Passenger . Is the replacement complete? | -- | -- | |
Is the passenger side air bag deployment loop resistance more than the specified value? | 4.4 ohms | |||
6 | Replace the inflatable restraint passenger seat harness. Is the replacement complete? | -- | -- | |
7 |
Is the harness connector damaged or corroded? | -- | ||
8 | Replace the IP harness. Are the repairs complete? | -- | -- | |
9 | Check for proper connection at terminals 13 and 14 on the SDM. Are the terminals damaged or corroded? | -- | ||
10 | Check for proper connection at terminals 13 and 14 on the SDM. Are the terminals damaged or corroded? | -- | ||
11 | Replace the inflatable restraint Sensing and Diagnostic and Seat Belt Pretensioner Module (SDM). Refer to Inflatable Restraint Sensing and Diagnostic and Seat Belt Pretensioner Module Replacement . Are the repairs complete? | -- | -- | |
Is the resistance reading within the specified values? | 0-0.5 ohms | |||
13 | Repair the open circuit or high resistance condition in CKT AM13. Is the repair complete? | -- | -- | |
Use the J 39200 to measure the resistance from the SDM harness connector terminal 14 to the inflatable restraint passenger seat module 2-way connector C209 terminal 2 Is the resistance reading within the specified values? | 0-0.5 ohms | Go to Integrity Check | ||
15 | Repair the open circuit or high resistance condition in CKT XM14. Is the repair complete? | -- | -- | |
16 | Reconnect all of the SIR components, make sure all the components are properly mounted. Have all the SIR components been reconnected and properly mounted? | -- | -- | |
17 | Clear all the SIR DTCs. Have all the DTCs been cleared? | -- | -- |
