Step
| Action
| Value(s)
| Yes
| No
|
DEFINITION:
RH front side door power window is inoperative from the RH front side door
window switch.
|
1
| Was the Power Window System Check performed?
| --
|
Go to Step 2
| Go to
Power Windows System Check
.
|
2
|
- Close all the doors.
- Disconnect the RH front side door window regulator motor connector.
- Use the DMM to measure the voltage between terminal 1 of the RH
front side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 4
|
Go to Step
3
|
3
|
- Locate an open or a high resistance in circuits A2 and/or A4.
- Repair the open or the high resistance in circuit A2 and/or A4.
Is the repair complete?
| --
|
Go to Step
13
| --
|
4
| Use the DMM to measure the resistance between terminal 4 of the RH front
side door window regulator motor connector and a known good ground.
Is the measured resistance within the specified value?
| Less than 5 ohms
|
Go to Step 6
|
Go to Step 5
|
5
|
- Locate an open or a high resistance in circuit F11.
- Repair the open or the high resistance in circuit F11.
Is the repair complete?
| --
|
Go to Step
13
| --
|
6
|
- Turn the ignition switch to the ON position.
- Use the DMM to measure the voltage between terminal 5 of the RH
front side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 8
|
Go to Step
7
|
7
|
- Locate an open or a high resistance in circuit B2 or B5.
- Repair the open or a high resistance in circuit B2 or B5.
Is the repair complete?
| --
|
Go to Step
13
| --
|
8
|
- Press the RH front side door window switch UP button.
- Use the DMM to measure the voltage between terminal 2 of the RH
front side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 10
|
Go to Step
9
|
9
|
- Locate an open or a high resistance in circuit RU6.
- Repair the open or the high resistance in circuit RU6.
- If this circuit is OK, replace the RH front side door window switch.
Refer to
Console Switch Housing Replacement
in Instrument Panel, Gauges and Console.
Is the repair or replacement complete?
| --
|
Go to Step 13
| --
|
10
|
- Press the RH front side door window switch DOWN button.
- Use the DMM to measure the voltage between terminal 3 of the RH
front side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 12
|
Go to Step
11
|
11
|
- Locate an open or a high resistance in circuits PA1 and/or PA2.
- Repair the open or the high resistance in circuits PA1 and/or
PA2.
- If these circuits are OK, replace the RH front side door window
switch. Refer to
Console Switch Housing Replacement
in Instrument Panel, Gauges and Console.
Is the repair or replacement complete?
| --
|
Go to Step 13
| --
|
12
| Replace the RH front side door window regulator motor.
Refer to
Front Side Door Window Regulator Replacement
in Doors.
Is the replacement complete?
| --
|
Go to Step
13
| --
|
13
|
- Connect all connectors and components that were disconnected.
- Verify that the RH front side door power window operates properly.
Does the RH front side door power window operate properly?
| --
| System OK
|
Go to Step 1
|
Step
| Action
| Value(s)
| Yes
| No
|
DEFINITION:
LH rear side door power window is inoperative from the LH rear side door window
switch.
|
1
| Was the Power Window System Check performed?
| --
|
Go to Step 2
| Go to
Power Windows System Check
.
|
2
|
- Cose all the doors.
- Disconnect the LH rear side door window regulator motor connector.
- Use the DMM to measure the voltage between terminal 1 of the LH
rear side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 4
|
Go to Step
3
|
3
|
- Locate an open or a high resistance in circuits A1 and/or A21.
- Repair the open or the high resistance in circuit A1 and/or A21.
Is the repair complete?
| --
|
Go to Step
13
| --
|
4
| Use the DMM to measure the resistance between terminal 4 of the LH rear
side door window regulator motor connector and a known good ground.
Is the measured resistance within the specified value?
| Less than 5 ohms
|
Go to Step 6
|
Go to Step 5
|
5
|
- Locate an open or a high resistance in circuit F1.
- Repair the open or the high resistance in circuit F1.
Is the repair complete?
| --
|
Go to Step
13
| --
|
6
|
- Turn the ignition switch to the ON position.
- Make sure that the rear window lockout switch is in the UNLOCK
position.
- If the rear window lockout switch is in the LOCK position, the
rear windows will not operate.
- Disconnect the LH rear side door window switch.
- Use the DMM to measure the voltage between terminal 7 of the LH
rear side door window switch connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 8
|
Go to Step
7
|
7
|
- Locate an open or a high resistance in the circuits M1 and/or
M3
- Repair the open or a high resistance in circuits M1 and/or M3.
- If these circuits are OK, replace the LH front side door window
switch. Refer to
Console Switch Housing Replacement
in Instrument Panel, Gauges and Console.
Is the repair complete?
| --
|
Go to Step
13
| --
|
8
|
- Connect the LH rear side door window switch.
- Press the LH rear side door window switch UP button.
- Use the DMM to measure the voltage between terminal 2 of the LH
rear side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 10
|
Go to Step
9
|
9
|
- Locate an open or a high resistance in circuits RU1 and/or RU2.
- Repair the open or the high resistance in circuits RU1 and/or
RU2.
- If these circuits are OK, replace the LH rear side door window
switch. Refer to
Rear Side Door Window Switch Replacement
in Doors.
Is the repair or replacement complete?
| --
|
Go to Step 13
| --
|
10
|
- Press the LH rear side door window switch DOWN button.
- Use the DMM to measure the voltage between terminal 3 of the LH
rear side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 12
|
Go to Step
11
|
11
|
- Locate an open or a high resistance in circuits PA1 and/or PA2.
- Repair the open or the high resistance in circuits PA1 and/or
PA2.
- If these circuits are OK, replace the LH rear side door window
switch. Refer to
Rear Side Door Window Switch Replacement
in Doors.
Is the repair or replacement complete?
| --
|
Go to Step 13
| --
|
12
| Replace the LH rear side door window regulator motor. Refer
to
Rear Side Door Window Regulator Replacement
in Doors.
Is the replacement complete?
| --
|
Go to Step
13
| --
|
13
|
- Connect all connectors and components that were disconnected.
- Verify that the LH rear side door power window operates properly.
Does the LH rear side door power window operate properly?
| --
| System OK
|
Go to Step 1
|
Step
| Action
| Value(s)
| Yes
| No
|
DEFINITION:
RH rear side door power window is inoperative from the RH rear side door window
switch.
|
1
| Was the Power Window System Check performed?
| --
|
Go to Step 2
| Go to
Power Windows System Check
.
|
2
|
- Close all the doors
- Disconnect the RH rear side door window regulator motor connector.
- Use the DMM to measure the voltage between terminal 1 of the RH
rear side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 4
|
Go to Step
3
|
3
|
- Locate an open or a high resistance in circuits A1 and/or A11.
- Repair the open or the high resistance in circuit A1 and/or A11.
Is the repair complete?
| --
|
Go to Step
15
| --
|
4
| Use the DMM to measure the resistance between terminal 4 of the RH rear
side door window regulator motor connector and a known good ground.
Is the measured resistance within the specified value?
| Less than 5 ohms
|
Go to Step 6
|
Go to Step 5
|
5
|
- Locate an open or a high resistance in circuit F1.
- Repair the open or the high resistance in circuit F1.
Is the repair complete?
| --
|
Go to Step
15
| --
|
6
|
- Turn the ignition switch to the ON position.
- Make sure that the rear window lockout switch is in the UNLOCK
position.
- If the rear window lockout switch is in the LOCK position, the
rear windows will not operate.
- Disconnect the RH rear side door window switch.
- Use the DMM to measure the voltage between terminal 7 of the RH
rear side door window switch connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 8
|
Go to Step
7
|
7
|
- Locate an open or a high resistance in the circuits M1 and/or
M4.
- Repair the open or a high resistance in circuits M1 and/or M4.
- If these circuits are OK, replace the LH front side door window
switch. Refer to
Console Switch Housing Replacement
in Instrument Panel, Gauges and Console.
Is the repair complete?
| --
|
Go to Step
15
| --
|
8
|
- Connect the RH rear side door window switch.
- Press the RH rear side door window switch UP button.
- Use the DMM to measure the voltage between terminal 2 of the RH
rear side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 10
|
Go to Step
9
|
9
|
- Locate an open or a high resistance in circuits RU1 and/or RU2.
- Repair the open or the high resistance in circuits RU1 and/or
RU2.
- If these circuits are OK, replace the RH rear side door window
switch. Refer to
Rear Side Door Window Switch Replacement
in Doors.
Is the repair or replacement complete?
| --
|
Go to Step 15
| --
|
10
|
- Press the RH rear side door window switch DOWN button.
- Use the DMM to measure the voltage between terminal 3 of the RH
rear side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 12
|
Go to Step
11
|
11
|
- Locate an open or a high resistance in circuits PA1 and/or PA2.
- Repair the open or the high resistance in circuits PA1 and/or
PA2.
- If these circuits are OK, replace the RH rear side door window
switch. Refer to
Rear Side Door Window Switch Replacement
in Doors.
Is the repair or replacement complete?
| --
|
Go to Step 15
| --
|
12
| Use the DMM to measure the voltage between terminal 5 of
the RH rear side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 14
|
Go to Step
13
|
13
|
- Locate an open or a high resistance in circuits B1 or B8.
- Repair the open or a high resistance in circuits B1 or B8.
Is the repair complete?
| --
|
Go to Step
15
| --
|
14
| Replace the RH rear side door window regulator motor. Refer to
Rear Side Door Window Regulator Replacement
in Doors.
Is the replacement complete?
| --
|
Go to Step
15
| --
|
15
|
- Connect all connectors and components that were disconnected.
- Verify that the RH rear side door power window operates properly.
Does the RH rear side door power window operate properly?
| --
| System OK
|
Go to Step 1
|
Step
| Action
| Value(s)
| Yes
| No
|
DEFINITION:
RH rear side door power window is inoperative from the RH front side door
window switch.
|
1
| Was the Power Window System Check performed?
| --
|
Go to Step 2
| Go to
Power Windows System Check
.
|
2
|
- Close all the doors.
- Disconnect the RH front side door window regulator motor connector.
- Use the DMM to measure the voltage between terminal 1 of the RH
front side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 4
|
Go to Step
3
|
3
|
- Locate an open or a high resistance in circuits A11 and/or A1.
- Repair the open or the high resistance in circuit A11 and/or A1.
Is the repair complete?
| --
|
Go to Step
13
| --
|
4
| Use the DMM to measure the resistance between terminal 4 of the RH front
side door window regulator motor connector and a known good ground.
Is the measured resistance within the specified value?
| Less than 5 ohms
|
Go to Step 6
|
Go to Step 5
|
5
|
- Locate an open or a high resistance in circuit F1.
- Repair the open or the high resistance in circuit F1.
Is the repair complete?
| --
|
Go to Step
13
| --
|
6
|
- Turn the ignition switch to the ON position.
- Disconnect the RH front side door window switch.
- Use the DMM to measure the voltage between terminal 5 of the RH
front side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 8
|
Go to Step
7
|
7
|
- Locate an open or a high resistance in circuit B1 or B8.
- Repair the open or a high resistance in circuit B1 or B8.
Is the repair complete?
| --
|
Go to Step
13
| --
|
8
|
- Press the RH front side door window switch UP button.
- Use the DMM to measure the voltage between terminal 2 of the RH
front side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 10
|
Go to Step
9
|
9
|
- Locate an open or a high resistance in circuit RU16 or RU2.
- Repair the open or the high resistance in circuit RU16 or RU2.
- If this circuit is OK, replace the RH front side door window switch.
Refer to
Console Switch Housing Replacement
in Instrument Panel, Gauges and Console.
Is the repair or replacement complete?
| --
|
Go to Step 13
| --
|
10
|
- Press the RH front side door window switch DOWN button.
- Use the DMM to measure the voltage between terminal 3 of the RH
front side door window regulator motor connector and a known good ground.
Is the measured voltage within the specified value?
| B+
|
Go to Step 12
|
Go to Step
11
|
11
|
- Locate an open or a high resistance in circuit PA4 or PA2.
- Repair the open or the high resistance in circuit PA4 or PA2.
- If this circuit is OK, replace the RH front side door window switch.
Refer to
Console Switch Housing Replacement
in Instrument Panel, Gauges and Console.
Is the repair or replacement complete?
| --
|
Go to Step 13
| --
|
12
| Replace the RH rear side door window regulator motor. Refer
to
Rear Side Door Window Regulator Replacement
in Doors.
Is the replacement complete?
| --
| | --
|
13
|
- Connect all connectors and components that were disconnected.
- Verify that the RH rear side door power window operates properly.
Does the RH rear side door power window operate properly?
| --
| System OK
|
Go to Step 1
|
