GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 1996 🢒 Roadmaster 🢒 Engine 🢒 Engine Electrical 🢒 Spark Plug Wires Not Operating Properly

Removal Procedure

    Notice: Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.

  1. Remove the left bank spark plug wire boots from the spark plugs.

    2. Object Number: 103023 Size: SH
  2. Remove the left bank spark plug wire harness support channel bolts and the channel.

    3. The rear bolt is located behind the exhaust manifold takedown. Loosen this bolt using a 10 mm wrench, then slide the channel upward to disengage the channel from the bolt.


    Object Number: 103027 Size: SH
  3. Remove the left bank spark plug wire harness from the clip located behind the air pump.
  4. Remove the right bank spark plug wire boots from the spark plugs.
  5. For vehicles equipped with a mechanical cooling fan, remove the following components:
    6. 5.1. Air intake resonator. Refer to Engine Controls.
    5.2. Remove the upper radiator fan shroud. Refer to Fan Shroud Replacement .
    5.3. Loosen the fan pulley nuts.
    5.4. Remove the fan belt.
    5.5. Remove the mechanical fan and the pulley.
    5.6. Remove the mechanical fan pulley brackets nuts.
    5.7. Remove the mechanical fan pulley bracket.
    5.8. Remove the radiator outlet pipe nuts from the A/C compressor mounting studs.
  6. Remove the accessory drive belt. Refer to Drive Belt Replacement .
  7. Raise and suitably support the vehicle. Refer to General Information.
  8. Remove the transmission oil cooler line support bolt/screw from the accessory drive bracket.
  9. Remove the accessory drive belt tensioner. Refer to Drive Belt Tensioner Replacement .
  10. Remove the A/C compressor attaching bolts/screws and the rear bracket nut.
  11. Reposition the A/C compressor to provide access to the front wire harness support.

    12. Object Number: 103032 Size: SH
  12. Remove the right wire harness support bolt.
  13. Remove the right wire harness support.
  14. Remove the left and the right bank spark plug wire harnesses from the distributor.

    15. Object Number: 106231 Size: SH
  15. Remove the left wire harness from the clips. Insert a screwdriver into the tab on top of the clip to disengage.

    16. Object Number: 106235 Size: SH
  16. Remove the right wire harness from the clips. Insert a screwdriver into the tab on top of the clip to disengage.

Installation Procedure

    Object Number: 106235 Size: SH
  1. Install the right wire harness to the clips.

    2. Object Number: 106231 Size: SH
  2. Install the left wire harness to the clips.

    3. Object Number: 106232 Size: SH
  3. Connect the left and right spark plug wire harness to the distributor as shown.
  4. Install the right wire harness to the harness support.
  5. Install the right wire harness support.

    6. Object Number: 103032 Size: SH
  6. Install the right wire harness support bolt/screw.

    7. Tighten
    Tighten the harness support bolt/screw to 40 N·m (30 lb ft).

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  7. Install the A/C compressor to the bracket.
  8. Install the A/C compressor fasteners.

    9. Tighten

        â€¢ Tighten the A/C compressor bolts/screws to 50 N·m (37 lb ft).
        â€¢ Tighten the A/C compressor rear bracket nut to 41 N·m (30 lb ft).
  9. Install the accessory drive belt tensioner. Refer to Drive Belt Tensioner Replacement .
  10. Install the transmission oil cooler line support bolt/screw.

    11. Tighten
    Tighten the oil cooler line support bolt/screw to 1.9 N·m (17 lb in).

  11. Lower the vehicle.
  12. Install the accessory drive belt. Refer to Drive Belt Replacement .
  13. If the vehicle is equipped with a mechanical fan, install the following components:
    14. 13.1. Install the radiator outlet pipe nuts.

    Tighten
    Tighten the radiator outlet pipe nuts to 16 N·m (12 lb ft).

    13.2. Install the mechanical fan pulley bracket nuts.

    Tighten
    Tighten the mechanical fan pulley bracket nuts to 50 N·m (37 lb ft).

    13.3. Install the mechanical fan pulley.
    13.4. Install the mechanical fan.
    13.5. Install the mechanical fan nuts. Finger tighten the nuts.
    13.6. Install the mechanical fan belt.

    Tighten
    Tighten the mechanical fan nuts to 26 N·m (19 lb ft).

    13.7. Install the upper radiator fan shroud. Refer to Fan Shroud Replacement .
    13.8. Install the air intake resonator. Refer to Engine Controls.
  14. Install the right bank spark plug wire boots to the spark plugs.
  15. Install the left bank sparkplug harness clip located behind the AIR pump.

    16. Object Number: 103023 Size: SH
  16. Install the left bank spark plug wire harness support channel.

    17. The rear bolt/screw is located behind the exhaust manifold takedown. Slide the channel onto the bolt/screw and then tighten using a 10 mm wrench.

  17. Install the left bank spark plug wire harness boots to the spark plugs.