GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 1999 🢒 Regal (China) (CNG) 🢒 Body and Accessories 🢒 Body Control System 🢒 DTC B2818 Low Tire Pressure System Reset Circuit Low

Object Number: 501914 Size: SF

Circuit Description

The BCM receives a momenitary ground signal from the Tire Inflation Reset Switch when the tires are inflated to the right amount and the customer presses the reset switch (located in the fuse block). The BCM then will send a classOverdrivemessage to the IP to turn off the LOW TIRE PRESSURE Indicator and reset the Low Tire Pressure system.

Conditions for Setting the DTC

The BCM detects a short to ground in circuit 1055 after 5 minutes.

Action Taken When the DTC Sets

The BCM stores DTC B2818 in memory.

Conditions for Clearing the DTC
    • The BCM detects a short to ground in circuit 1055.
    • A history DTC will clear after 100 consecutive ignition cycles if the condition for the malfunction is no longer present.
    • Using a scan tool.

Diagnostic Aids
    • An intermittent malfunction may cause an intermittent short to ground in circuit 1055.
    • The BCM is shorted to ground internally.
    • If the DTC is a history DTC, the problem may be intermittent. Try performing the tests shown while moving wiring and connectors, this can often cause the malfunction to reappear.
    • DTC P1626 will set in the Powertrain Control Module (PCM) when the ignition switch is on with the Body Control module (BCM) disconnected. When BCM diagnostics and repairs are completed, refer to Powertrain On Board Diagnostic (OBD) System Check

Test Description

The number(s) below refer to the step number(s) on the diagnostic table.

  1. This step checks for ground in circuit 1055.

    2.

  2. The step determines whether the short to ground is in circuit 1055 or the tire inflation reset switch.

    3.

  3. This step determines where the malfunction is in intermittent or the BCM is faulty.

Step

Action

Value(s)

Yes

No

1

Was the BCM Diagnostic System Check performed?

--

Go to Step 2

Go to Diagnostic System Check - Body Control System

2

  1. Turn the ignition switch to the OFF position.
  2. Disconnect the Body Control Module (BCM) connector C1.
  3. Turn the ignition switch to the ON position.
  4. Using a test light connect between the BCM harness connector C1 terminal C10 and B+.

Is the test light on?

--

Go to Step 3

Go to Step 4

3

  1. Leave the test light in the same location from the previous step.
  2. Disconnect the Tire Inflation Reset Switch.

Is the test light on?

--

Go to Step 5

Go to Step 6

4

  1. Turn the ignition switch in the OFF position.
  2. Reinstall connectors/components removed.
  3. Turn the ignition switch in the ON position.
  4. Clear BCM DTCs. Refer to Clearing DTCs for more information.
  5. Wait 5 minutes.
  6. Check for BCM DTCs. Refer to Diagnostic Trouble Code (DTC) Displaying for more information.

Does the BCM B2818 reset as a current DTC?

--

Go to Step 7

Go to Step 8

5

Repair a short to ground in circuit 1055 between the BCM connector C1 terminal C10 and the tire inflation reset switch connector terminal B9.

Is the repair complete?

--

Go to Step 9

--

6

Replace the tire inflation reset switch.

Is the repair complete?

--

Go to Step 9

--

7
  1. Replace the BCM. Refer to Body Control Module Replacement for more information.
  2. After replacing the BCM, perform the Setup New BCM procedure. Refer to Body Control Module (BCM) Programming/RPO Configuration for more information.

Is the repair complete?

--

Go to Step 9

--

8

The malfunction is not present. Refer to Diagnostic Aids for additional information regarding DTC.

Is the repair complete?

--

Go to Step 9

--

9
  1. Turn the ignition switch to the OFF position.
  2. Reinstall connectors/components removed.
  3. Turn the ignition switch to the On position.
  4. Clear BCM DTCs. Refer to Clearing DTCs for more information.
  5. Check for BCM DTCs. Refer to Diagnostic Trouble Code (DTC) Displaying for more information.

Are there current BCM DTCs set?

--

Go to Diagnostic System Check - Body Control System

System OK