Circuit Description
The low oil pressure sensor is normally closed. When oil pressure increases is above 1 to 4.5 psi the switch contacts open. The PCM supplies 12 volts to the oil pressure input circuit. With low oil pressure the 12 volts is pulled low to ground. This diagnostic tests for a open condition of the oil pressure switch circuit. If the engine has been OFF long enough for engine temperature to drop by 10°C, then a shorted (low oil pressure) condition of the circuit should be observed prior to engine running. If the engine has not been cranked and oil pressure has been detected. DTC P1189 will set.
Conditions for Running the DTC
| • | Codes P0117, P0118 and P1114 not set. |
| • | Ignition ON |
| • | Engine OFF |
| • | Engine temperature 10°C less than last key OFF temperature. |
Conditions for Setting the DTC
Circuit open for 10 seconds
Action Taken When the DTC Sets
| • | The malfunction indicator lamp (MIL) will not illuminate. |
| • | No message will be displayed. |
Conditions for Clearing the MIL/DTC
| • | A History DTC will clear after forty consecutive warm-up cycles with no failures of any non-emission related diagnostic test. |
| • | A current DTC will clear when the diagnostic runs and does not fail. |
| • | Use a scan tool to clear DTCs. |
Diagnostic Aids
Check the oil pressure sensor input and ground circuits for an intermittent open or poor oil pressure sensor terminal contact. With the engine OFF the oil pressure display on the scan tool should indicate LOW. An open sensor/circuit would indicate OK with the engine OFF.
This DTC only tests the oil pressure circuit for an open condition.
If the DTC cannot be duplicated and is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set. Also refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
Test Description
The numbers below refer to steps in the diagnostic table.
-
This step checks that the fault is present. Low should be displayed with the engine not running if the fault is not present.
-
This step checks if the oil pressure switch or wiring is at fault.
-
This step checks if the oil pressure switch input circuit or the PCM is at fault.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Instrument Cluster Diagnostic System Check? | -- | Go to Step 2 | |
Does the scan tool indicate low oil pressure? | -- | Go to Step 10 | Go to Step 3 | |
Does the scan tool indicate oil pressure low? | -- | Go to Step 6 | Go to Step 4 | |
Is the resistance the same or less than the value specified? | 5 ohms | Go to Step 7 | Go to Step 5 | |
5 | Repair the open in either the oil pressure sensor input circuit or the oil pressure sensor ground circuit. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | -- |
6 | Inspect for poor connections at the harness connector of the oil pressure sensor connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 8 |
7 | Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 |
8 | Replace the oil pressure sensor. Refer to Engine Oil Pressure Sensor or Switch Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- |
9 |
Important: The replacement PCM must be programmed. Replace the PCM. Refer to Powertrain Control Module Replacement (2.5L) in Engine Controls. Did you complete the replacement? | -- | Go to Step 10 | -- |
10 |
Does the DTC reset? | -- | Go to | System OK |
