The switch or switch circuit that failed and generated this DTC is wired to one of the passenger door modules. The passenger door modules each supply battery voltage to the contacts of both the up and down signal circuits of their respective power window switch. Each passenger door module also supplies a ground circuit to the associated power window switch. When the normally open contacts of the switch are closed to ground, the associated passenger door module interprets this switch signal and assigns it a digital message. The passenger door module then sends this message over the power door serial data circuit to the driver door module (DDM).
This diagnostic procedure supports the following DTCs:
• | DTC B2202 RF Window Switch Stuck in Up Position |
• | DTC B2203 RF Window Switch Stuck in Down Position |
• | DTC B2204 LR Window Switch Stuck in Up Position |
• | DTC B2205 LR Window Switch Stuck in Down Position |
• | DTC B2206 RR Window Switch Stuck in Up Position |
• | DTC B2207 RR Window Switch Stuck in Down Position |
The DDM and the passenger door module associated with the failed power window must be powered and can not have B1327 - Battery Voltage Low or B1328 - Battery Voltage High set for one of these DTCs to set. If one of the DTCs indicating a loss of communications with a door module is set, the setting of DTCs from that module is prohibited.
If the DDM receives a message from a passenger door module indicating that a window switch is closed for more than 15 continuous seconds, the DDM sets the DTC.
The action taken depends on which switch contacts are closed to ground:
• | If an UP switch is closed for more than 15 seconds, both UP and DOWN movement is prohibited. |
• | If a DOWN switch is closed for more than 15 seconds, the DOWN movement is prohibited but UP movement is permitted. |
The DDM clears this current DTC when the switch message is not received, or when the module power mode changes from OFF to RUN, and stores the DTC as history. The history DTC will clear either after 50 OFF/ON ignition switch cycles without a repeated failure, or in response to a scan tool command.
The numbers below refer to the step numbers on the diagnostic table.
This step checks the module input state using the normal input status.
This step checks to see that the input is seen by the module.
This step checks to see that the signal lines to the module are open with the switch removed.
This step checks to see that the signal circuits are not shorted.
Step | Action | Yes | No |
---|---|---|---|
Schematic Reference: Power Window Schematics Connector End View Reference: Master Electrical Component List in Wiring Systems | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
Does the scan tool display Idle? | Go to Step 3 | Go to Step 4 | |
Does the Door Window Switch parameter change from Idle to Up and Down? | Go to Testing for Electrical Intermittents in Wiring Systems | Go to Step 4 | |
Does the scan tool display Idle? | Go to Step 7 | Go to Step 5 | |
Test the signal circuits of the inoperative passenger door window switch for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 10 | Go to Step 6 | |
6 | Inspect for poor connections at the harness connector of the inoperative passenger door control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 10 | Go to Step 8 |
7 | Inspect for poor connections at the harness connector of the inoperative passenger door window switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 10 | Go to Step 9 |
8 | Replace the inoperative passenger door control module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | Go to Step 10 | -- |
9 | Replace the inoperative passenger door window switch. Refer to Front Door Switch Replacement or Rear Side Door Window Switch Replacement . Did you complete the replacement? | Go to Step 10 | -- |
10 |
Does the DTC reset? | Go to Step 2 | System OK |