Schematic Reference: HVAC Schematics

Connector End View Reference: HVAC Connector End Views

DEFINITION: The A/C compressor clutch will not disengage when an A/C request has not been made and a Powertrain DTC has not been set.

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

1. Start the engine.
2. Place the blower motor switch in the OFF position.
3. Place the A/C switch in the OFF position.

Does the A/C compressor operate?

Go to Step 3

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

With the scan tool, observe the A/C Relay Command parameter in the powertrain control module (PCM) engine data list.

Does the scan tool indicate the A/C Relay Command parameter is ON?

Go to Step 4

Go to Step 7

With the scan tool, observe the Control Head (desired) parameter in the body control module (BCM) A/C information list.

Does the scan tool display OFF?

Go to Step 5

Go to Step 12

With the scan tool, observe the A/C Requested parameter in the HVAC system data list.

Does the scan tool display NO?

Go to Step 6

Go to Step 13

With a scan tool, observe the A/C Clutch (desired) parameter in the BCM A/C information list.

Does the scan tool display OFF?

Go to Step 15

Go to Step 14

1. Turn OFF the ignition.
2. Disconnect the A/C compressor clutch relay.
3. Turn ON the ignition, with the engine OFF.

Does the A/C compressor clutch disengage?

Go to Step 8

Go to Step 9

Test the A/C compressor clutch relay control circuit of the A/C compressor clutch relay for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 11

Test the A/C compressor clutch supply voltage circuit of the A/C compressor clutch relay for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 10

Inspect for poor connections at the harness connector of the A/C compressor clutch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 17

Inspect for poor connections at the A/C compressor clutch relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 16

Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 18

Inspect for poor connections at the harness connector of the instrument panel integration module (IPM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 19

Inspect for poor connections at the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 20

Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 21

Replace the A/C compressor clutch relay. Refer to Compressor Relay Replacement in Heating, Ventilation and Air Conditioning.

Did you complete the replacement?

Go to Step 22

--

Replace the A/C compressor clutch. Refer to Compressor Clutch Plate and Hub Assembly Removal and Compressor Clutch Plate/Hub Assembly Install in Heating, Ventilation and Air Conditioning.

Did you complete the replacement?

Go to Step 22

--

Replace the HVAC control module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 22

--

Replace the IPM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 22

--

Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 22

--

Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 22

--

Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 2