Important: If the vehicle has been in a collision, refer to Repairs and Inspections Required After a Collision for additional information.

Perform the following inspection from the driver seat:

1. Turn the ignition switch to the ON position. Verify proper operation of the seat belt reminder lamp with the belt buckled and with the belt unbuckled. Refer to Seat Belt System Description and Operation .
2. Inspect the shoulder belt guide in order to ensure that the following conditions are met:

•	The seat belt webbing is seated flatly in the guide slot.

•	The seat belt webbing does not bind.

3. Verify that the seat belt buckle faces inboard and is accessible.
4. Verify that the seat belt retractor units are securely attached.
5. Verify that the seat belt anchor bolts are secure.
6. Fully extend the seat belt webbing. Verify that the seat belt webbing does not have any twists or tears.
7. Allow the seat belt webbing to retract. Verify that the seat belt webbing returns freely and completely back into the retractor. If the seat belt webbing will not retract, refer to Seat Belt Does Not Retract .
8. Snap the seat belt latch plate into the buckle.
9. Sharply tug on the seat belt latch plate and the buckle. Verify that the seat belt latch plate and the buckle remain locked when tugged.
10. Push the button on the buckle:

10.1.

Verify that the seat belt latch plate releases easily from the buckle.

10.2.

Verify that the button returns to its original position.

Perform the following inspection procedures from the passenger seat:

1. Verify the Automatic Locking Retractor (ALR) feature operates properly by performing the following checks:

1.1.	Pull the seat belt all the way out of the retractor until it stops.

1.2.	Slowly allow the belt to retract partially, while listening for a ratcheting sound.

1.3.	Sharply tug on the belt ensuring that the retractor lock sets and does not allow the belt to be pulled from the retractor.

1.4.	After performing steps 1.1 through 1.3 ensure the belt fully retracts.

2. Repeat the inspection procedure steps 2 through 10 performed for the drivers seat.

Perform the following steps in order to inspect the front and rear center seat belts if equipped:

1. Verify that the center seat belts are accessible.
2. Verify that the center seat belts have no twists or tears in the webbing.
3. Verify that the seat belts are securely attached.
4. Verify that the seat belt anchor bolts are properly torqued.
5. Snap the center seat belt latch plates into the buckles.
6. Sharply tug on the seat belt latch plates and the buckles. Verify that the seat belt latch plates and the buckles remain locked when tugged.
7. Push the button on the buckles:

7.1.	Verify that the seat belt latch plates releases easily from the buckles.

7.2.	Verify that the buttons return to their original position.

Repeat the inspection procedure steps 2 through 10 performed for the drivers seat for the two rear outboard seatings positions.

Caution: Perform this test in an area clear of other vehicles or obstructions. Do not conduct this test on the open road. A large, empty parking lot is suitable. Failure to observe this precaution may result in damage to the vehicle and possible personal injury.

1. Fasten the seat belts, an assistant is needed when the retractor under test is not part of the driver seat belt.
2. Accelerate the vehicle slowly to 16 km/h (10 mph) and apply the brakes firmly.
3. Verify that the seat belt locks when braking firmly.

Important: When performing this check, note the position that the retractors are mounted. Some retractors are not mounted at a zero degree inclination.

4. If the belt does not lock, proceed with the following steps:

4.1.	Remove the seat belt retractor assembly.

4.2.	Tilt the seat belt retractor slowly.





4.3.	Ensure that the seat belt webbing can be pulled from the retractor at an inclination of 15 degrees or less and cannot be pulled from the retractor at an inclination of 45 degrees or more.

4.4.	If the seat belt retractor does not operate as described, replace the retractor assembly. Refer to the appropriate service procedure in the seat belt section of the service manual.