| Table 1: | Door Travel Value |
Circuit Description
The rear junction block supplies ignition voltage through CKT 541 (BRN). The heater and A/C programmer commands the actuator to move by suppling voltage on the command line CKT 1318 (YEL). The command line voltage and motor actions are as follows:
| • | 0 volts moves toward full hot. |
| • | 2.5 volts stops the motor. |
| • | 5 volts moves toward full cold. |
The heater and A/C programmer determines the current position by monitoring the voltage on the feedback CKT 892 (DK GRN). A feedback potentiometer supplies a regulated 5 volt signal by the heater and A/C programmer on CKT 705 (GRY), and a ground from the heater and A/C programmer CKT 1791 (YEL). The pot is gear driven inside the actuator. The feedback voltage is a function of the motor position with a high voltage of 4-5 volts indicating full cold door position. A low voltage of less then 1 volt indicates the full hot position. Operation of the air mix door actuator can be evaluated through Scan Tool data.
Conditions for Setting the DTC
| • | The ignition is on. |
| • | The feedback circuit is open or shorted. |
Action Taken When the DTC Sets
| • | A default value of 128 counts will be used by the Heater and A/C programmer. |
| • | This default value results in only 2 positions of the actuator A/C and Defrost being used by the system. |
Conditions for Clearing the DTC
| • | Use a Scan Tool . |
| • | A history DTC will clear after 50 consecutive ignition cycles have occurred without a malfunction. |
| • | Battery voltage to the body control module is interrupted. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
Perform the Body Control Module (BCM) Diagnostic Symptom Check before continuing with the diagnosis of this DTC.
-
This test allows the Scan Tool to recalibrate the actuator.
Step | Action | Value(s) | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
Did you perform the BCM Diagnostic System Check? | -- | Go to Step 2 | Go to Diagnostic System Check - Body Control System in Body Control System | |||||||
Is the door being commanded to the proper values? | -- | Go to Step 3 | Go to Step 8 | |||||||
3 | Compare the actual high and low stop values with shown on the Scan Tool with the values listed in the door travel table below. Are the values within the specified ranges? | -- | Go to Step 8 | Go to Step 4 | ||||||
4 |
Are any of the actuator CKTs faulty? | -- | Go to Step 7 | Go to Step 5 | ||||||
5 | Inspect the suspect actuator door for the proper alignment, a broken shaft bushing, obstructions, etc. Are any of these conditions present? | Go to Step 6 | Go to Step 9 | |||||||
6 | Repair the actuator. Did you complete the repair? | -- | Go to Diagnostic System Check - Body Control System in Body Control System | -- | ||||||
7 | Repair the suspect CKT. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 8 | -- | ||||||
8 | Replace the heater and A/C programmer. Refer to Programmer Replacement . Did you complete the repair? | -- | Go to Diagnostic System Check - Body Control System in Body Control System | -- | ||||||
9 | Replace the suspect actuator. Refer to Programmer Replacement or to Air Mix Actuator Replacement - Passenger . Did you complete the repair? | -- | Go to Diagnostic System Check - Body Control System in Body Control System | -- |
Actuator | "Com" High | "Com" Low | Act High | Act Low |
|---|---|---|---|---|
Air Mix #1 (Driver) | 245 | 10 | 198 - 206 | 41 - 47 |
Air Mix #2 (Pass) | 198 - 207 | 48 - 57 | ||
Def/Heat Door | 178 - 188 | 59 - 72 | ||
A/C Door | 188 - 197 | 51 - 60 | ||
Air Inlet Door | 213 - 221 | 38 - 47 |
