The keyless entry system is a supplementary vehicle entry device. Radio frequency interference or discharged batteries may disable the system.
Keyless entry allows you to operate the following features:
• | The rear compartment lid release--Press and release rear release button to activate. |
• | The illuminated entry lamps |
The keyless entry system has the following main components:
• | The body control module (BCM) |
• | The remote control door lock receiver (RCDLR)--When you press a button on the transmitter, the transmitter sends a signal to the RCDLR. The RCDLR receives the signal and sends a serial data message requesting the appropriate function
from the BCM. |
• | Keyless Entry Antenna which is a coaxial cable that runs from the RCDLR to the back glass. It attaches with a 9 volt battery style connection to a grid on the back glass, this style antenna is used to increase range and performance for Keyless
Entry and Remote Vehicle Start systems . |
Unlock Driver Door Only
Momentarily press the UNLOCK button in order to perform the following functions:
• | Unlock the driver door only. |
• | Illuminate the interior lamps for approximately 20 seconds or until the ignition is turned ON. |
• | Flash the park lamps if the ignition is turned OFF and the doors are closed. |
• | Identify the driver to the radio--The radio will then revert to the station presets, the last station, the last volume settings, and the last playback mode used by that driver. |
Unlock All Doors - Second Operation
Momentarily press the UNLOCK button a second time, within 5 seconds of the first press, in order to perform the following functions:
• | Unlock all of the doors. |
• | Illuminate the interior lamps for approximately 20 seconds or until the ignition is turned ON. |
Lock All Doors
Press the LOCK button in order to perform the following functions:
• | Lock all of the doors. |
• | Immediately turn OFF the interior lamps. |
• | Flash the park lamps if the ignition is OFF and the doors are closed. |
• | Chirp the horn if the ignition is OFF and the doors are closed. |
Panic Alarm Function
A single press of the panic button performs the following functions:
• | Illuminates the interior lamps |
• | Flashes the daytime running lamps for 2 minutes or until the following conditions occur: |
- | The panic button is pressed again. |
- | The ignition switch is turned to the RUN position with a valid key. |
Remote Vehicle Start
The Remote Vehicle Start function allows the customer to start the vehicle while not in the car. It also allows starting up the vehicle heating or air conditioning system and other vehicle systems to provide the customer with a comfortable vehicle when
they enter it. The distance the customer can be away from the vehicle and operate this feature has a design requirement of 150 meters. The Remote Vehicle Start feature is started by the customer pressing and releasing the lock button and then pressing
and holding the remote vehicle start (RVS) buttons on their key fob. The turn signal lamps will flash if this feedback is enabled on to indicate the vehicle has received the Remote Start Request. Each time the customer does a remote vehicle start, the vehicle
doors are locked, however they may then be unlocked/locked with the key fob or key at anytime. Once the vehicle has been started, there is visible feedback. There are vehicle conditions which will prevent a remote start, for example if the hood is not closed
or the key is in the ignition. The Remote Vehicle Start feature once activated is allowed to run for 10 minutes. At any time during this 10 minute time the 10 minute time-out can be reset once. This feature is called a Remote Vehicle Start
Continue. This allows a maximum of 20 minutes of engine running via the Remote Vehicle Start feature without a reset. If the Remote Vehicle Start Continue is done at 7 minutes into the initial 10 minute time-out, a total of 17 minutes
of engine running would occur. A remote vehicle start, once active, can be stopped by pressing a dedicated RVS button on the key fob or by pressing the Vehicle Hazard switch located inside the vehicle . the following will also abort a remote start, using an
invalid passkey , force rotating the ignition, force shifting out of park. Remote start will also be stopped if any DTCs that turn ON the SES/MIL are stored in history or current status.
Customer Programming Method for Enabling/Disabling the RVS Feature
Using the driver information center (DIC), the remote vehicle start (RVS) feature can be DISABLED and ENABLED just like other items programmable via the DIC.
If your vehicle does not have the DIC feature, and remote vehicle start was installed at the dealership, you will need to have the dealership enable or disable the remote vehicle start system.
Remote Vehicle Start Features That Allow A Remote Vehicle START/CONTINUE
• | The remote vehicle start (RVS) feature must be enabled. |
• | A remote vehicle start request command is received by the body control module (BCM). |
• | The hood ajar switch status is closed. |
• | The number of remote start attempts is less than 3. |
• | The key is not in the ignition. |
• | The remote start voltages are within proper operating ranges 6-16 volts. |
• | There are no DTCs or serial data communication failures with RVS related systems. |
• | The transmission status is Park/Neutral and the vehicle speed is zero. |
Conditions to Stop A Remote Vehicle Start
• | Hood ajar switch status is - OPEN. |
• | Inserting the key in the ignition and turning the key to any non-off power modes, and returning the key to the OFF position |
• | The remote vehicle start (RVS) time has elapsed or timed out. |
• | The RVS master receives a run abort message from the engine control module (ECM). |
• | Hazard shutoff switch status is - ACTIVE. |
• | By content theft deterrent (CTD) system, if equipped, and alarm status becomes Violated |
• | RVS system voltage out of range, under 6 volts or over 16 volts |
• | DTCs set for any related systems, or serial data communication failure for any modules that support the RVS function |
If the RVS master stops a remote vehicle start for any of these conditions, further remote vehicle starting is not allowed until a RVS RESET has occurred.
A RVS Reset occurs when, in an ignition switch vehicle, the key is inserted and rotated into the Run position, power mode of RUN is seen, and ECM Vehicle Theft Fuel Continue is received over serial data and passes VTD criteria.
This action results in resetting the RVS counters to MAX starts allowed and the RVS Attempts to 0.